Models > KGCT305AAL0

KGCT305AAL0 KitchenAid Cooktop

Jump to:

Find Part by Name

Diagrams for KGCT305AAL0

Viewing 4 of 4

BURNER BOX, GAS VALVES, AND SWITCHES

COOKTOP, BURNER AND GRATE

SEALED GAS BURNER KIT

WIRING HARNESS

Most Popular Parts for KGCT305AAL0

Viewing 12 of 69

Knob Skirt - Black

$11.18

Knob Skirt

★★★★★

(1)

$11.07

This part goes around the back of the knob.

Control Knob

$24.75

Sold individually. This knob accepts a D-shaped shaft.

Control Knob

$25.38

Sold individually. This knob can accept a D-shaped shaft.

Spark Electrode

$49.02

This part helps your burner ignite and produce flame.

Burner Control Knob

$31.39

Sold individually. This knob takes a D-shaped shaft.

Knob Skirt - Black

$9.10

NOTE: No longer available in biscuit or white. Black only.

Spark Module

$213.61

This spark module uses a high voltage spark discharge to the switch to ingnite the gas.

Igniter Switch

$47.17

This is a switch that creates the spark that lights the gas and starts the burners. When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.

Gas Valve/Switch Seal Cover

$35.28

Part is located on top of the igniter switch that's next to the gas valve. Helps regulate gas flow and the amount of normal leakage that may occur.

Valve Screw

Part might differ in appearance, but functions same as original. Sold individually.

Burner Grate Pad Kit

There are 5 included in this kit.

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for KGCT305AAL0

Viewing 3 of 3

Will Not Start

Fixed by these parts

How to fix it

Gas igniter glows, but will not light

Fixed by these parts

How to fix it

Element will not heat

Fixed by these parts

How to fix it

Installation Instructions for KGCT305AAL0 Provided by Fix customers like you

Viewing 3 of 20

Customer:: John from Waterford, MI
Parts Used:: WP4454392
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Wrench (Adjustable)

Sparker would not quit sparking after lighting the gas.

Turned off the gas then disconnected the gas line. Unplugged the AC cord and removed the unit from the counter top. Had to locate a suitable area to lay the cooktop, rather large. The bottom cover is held on by 6-8 sheet metal screws, however, the gas regulator and nipple must be removed also for the cover to come off. I removed the Ignit ... Read more

Read less

35 of 46 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Billy from Martinsville, IN
Parts Used:: WP3185804
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

There was a crack in the porcelain not letting it spark

I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.

22 of 35 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Joe from San Bruno, CA
Parts Used:: WP3185804
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Screw drivers, Wrench (Adjustable)

broken ignitor insulation; repeated sparking after burner lit

Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!

15 of 21 people found this instruction helpful.

Was this instruction helpful to you?