Models > 91133389100

91133389100 Kenmore Cooktop

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Manuals & Guides for 91133389100

Click to download
Keep searches simple, eg. "belt" or "pump".
This is a replacement drip bowl for your range or oven. The drip bowl sits beneath the burner element and collects any drips or spills. This drip bowl is 8 inches in diameter and is used to replace th...
No Longer Available
This part helps your burner ignite and produce flame.
In Stock
This burner drip bowl is sold individually. It is white on the top side, and black underneath.
In Stock
This part is the replacement burner bowl seal or drip pan seal for your range. It is black in color and is sold individually. The burner bowl seal creates a seal between the cooktop and the drip pan a...
In Stock
$11.59
In Stock
$125.55
Sold Individually.
In Stock
$127.29
Sold individually.
In Stock
This black drip bowl is sold individually.
In Stock
This burner bowl, also known as a drip pan, is a legitimate OEM replacement part for your stove. Turn off power to the unit when conducting this repair. You will need to unscrew the existing burner bo...
In Stock
$7.76
Sold Individually.
In Stock
This burner drip bowl is sold individually. It is white on the top side, and black underneath.
In Stock
This gasket goes under the burner bowl to help protect the glass from high heat. Sold individually.
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 91133389100

Viewing 2 of 2
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Thomas from Bloomsbury, NJ
Parts Used:
WB13K18
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the w ire. It is not clear and can go on either way.
37 of 63 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Littleton, CO
Parts Used:
WB18T10344, WB13X32509
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
No spark to ignite the gas.
First I shut off the gas valve below the range and unplugged the unit from the electrical outlet. I left the flexible gas line fitting undisturbed/attached to the range top gas fitting. Then I removed the two screws below the unit (under the counter) that affix the range to the counter/support structure. Then I removed all of the knobs and burner grills and gas diffusers sitting on the top of the range. Then I lifted out the burner bowls and disconnected each from their respective spark wires. Then I gently pried the range from its hole in the counter being carefulm not to break the glass top and lifted it out turned it at an angle to the counter top hole and set it back down on the counter. Then I gently pried off the glass top from the metal range base, cleaned it thoroughly and set it aside. Then, I placed the new spark module next to the old one and one by one I transferred each wire to its respective location on the new module. The instructions pointed out that the new spark module has a revised grounding scheme and that a ground wire is no longer needed, so I removed and discarded the green ground wire. I then affixed the new spark module into the location where the old spark module had been. Next I replaced the wiring harness which contains the switches for each burner location. It is important to replace the wiring harness along with the spark module as they must work together reliably to complete the gas ignition circuit. The old wiring harness simply lifts/unsnaps out and the new one snaps into its place. Once both the spark module and wiring harness were in place, reassembly of the range was simply the reverse of disassembly.
24 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Bakersfield, CA
Parts Used:
WB31T10006, WB29K47, WB29K44, WB29K41
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My wife wanted different color stove top grate & burner caps.
Called GE for part number crossover from gray to black and asked for an email quote. Called Parts Select for pricing, which was alot lower! Shipping took five days and less then $8.00 buck....now mama's happy!!!! Thanks for great frendly service from Mike in California.
19 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!