91132255590 Kenmore Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Logansport, IN
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Top four burners on oven would not light without using match
Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. There are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bloomsbury, NJ
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Tulsa, OK
- Parts Used:
- WB24T10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
electronic ignitors would not stop firing even when burner was off
first I removed all the srews from the burners that hold the glass cooktop. I then disconected the two wires from the damaged gas valves and replaced them all four with the new ones. After that I put it all togehter and work just fine and celebrated with a good cold beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Maurertown, VA
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Spark was present in only two of four burners
Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aloha from Monterey, LA
- Parts Used:
- WB28K145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacement cook-top, had natural gas orifices, needed propane
Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angie from Acworth, GA
- Parts Used:
- WB31T10004, WB31K5092, WB31K5091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Porcelain Gas Burner Bowls Chipped
I have a GE Profile Gas Range that was installed by the builder in 1997. The porcelain bowl under the grate had chipped on all the elements. I replaced them easily..quickly...and was very cost effective...thanks for the great service...great site to order from. AC
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Villa Park, IL
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
stove top burner ignition spark progressively got weaker and then stopped on all but one burner.
I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chadd from philadelphia, PA
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
2 burners wouldnt spark
Took top off, removed wires from old spark module and put them on new one. Very easy and quick, works very well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Freehold, NJ
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Only one burner sparking on range.
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Irvine, KY
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode ceramic insulator was cracked
First I elevated range top, then removed cracked electride from connector pin. Installed new electrode and lowered range top and all was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Dacula, GA
- Parts Used:
- WB31K5091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bowls were 14+ years old and needed replacement
Very easy once I got the right parts - when I ordered I didn't realize that the center holes were what determined whether I needed "small" or "medium/large"...I was going by the exterior dimensions I returned 3 of the 4 I ordered and re-ordered the right size. My wife ended up replacing the rest of them herself after watching me do the one that did fit. Looks like a new stove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from NASHVILLE, TN
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced igniter pins but no joy, needed igniter module
Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from new hope, PA
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burners began to fail to ignite.
Removed six screws on the back panel. Just switched six wires from the old to the new module. Stove burners work perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Washington, NC
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range burners would not light
Lift up work light cover. Remove lamp. Remove two screws from control panel. Lift up control panel. Pop out spark module from slots. Remove the 6 wires from module. Attach wires to new module - module has a diagram on it that shows where wires are attached. Push new module back into slots. Replace control panel cover, lamp, and work light. Now the burners light - the spark is MUCH stronger than before repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eve and from MIDLAND, MI
- Parts Used:
- WB24T10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
One burner would not ignite.
I replaced the igniter under the knob.
Was this instruction helpful to you?
Thank you for voting!