Models
>
62942769
62942769 Kenmore Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Manuals & Guides for 62942769
Click to downloadKeep searches simple, eg. "belt" or "pump".
This grease filter is sixteen and a half inches long and nine inches wide. It is made of metal and is intended for use with downdraft ranges and cooktops.
In Stock
In Stock
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
In Stock
This part is used as a support for the grill element. Sold individually.
No Longer Available
$47.69
This cartridge receptacle is almost four inches long. It is white in color and is made of ceramic.
In Stock
$45.50
This jar is a little over five inches long. It is made of glass and is used for collecting the grease drippings of gas ranges.
In Stock
This is a burner cartridge terminal block for your range/cooktop. If you are having trouble with your elements heating up, this part may need to be replaced. It does not come with spades or wiring. Th...
In Stock
On Order
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 62942769
Viewing 4 of 4Element will not heat
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Oven is too hot
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James H from Oxford, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner had one temperature--hot, regardless of setting
1. Killed power and removed the regulator's knob, noted the position of the old control.
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in ... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in ... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnnie from Daphne, AL
- Parts Used:
- WPY706012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Grease Filter For Downdraft Stove Top
Lift off blower vent cover. Lift out old filter. Clean walls and bottom of down draft using degrease soap and warm water. Dry. Discovered my grease filter will not install diagonally as shown in unit manual. Decided to drop into downdraft and put in front of fan suction. Found this left a gap at the top of fan suction that was not co
... Read more
vered by the filter. Cut piece of wood 1 inch thick and width and length to drop down in the downdraft and lay on bottom. Set filter on top of wood in front of the fan suction. Verified that fan suction would pull filter tight against the opening by turning fan on and off. Put vent cover back over downdraft and told wife I was done.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Mohnton, PA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner Control not Functioning
Simple Repair!
Turn off Power
Remove four screws under panel.
Remove old burner knob.
Drop Burner Panel from range
Remove 5 wire connectors from old burner control
with pliers
Remove 2 screws that held burner control to range
panel
Install new burner control
Rplace two screws to burner ... Read more control
Replace 5 wire connectors to new burner control
Replace 4 screw under panel
Replace knob to new burner control
Turn on electricity
Made wife happy!
Turn off Power
Remove four screws under panel.
Remove old burner knob.
Drop Burner Panel from range
Remove 5 wire connectors from old burner control
with pliers
Remove 2 screws that held burner control to range
panel
Install new burner control
Rplace two screws to burner ... Read more control
Replace 5 wire connectors to new burner control
Replace 4 screw under panel
Replace knob to new burner control
Turn on electricity
Made wife happy!
Read less
Was this instruction helpful to you?
Thank you for voting!