Models
>
JGC8645ADW
JGC8645ADW Jenn-Air Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGC8645ADW
Viewing 3 of 3
Manuals & Guides for JGC8645ADW
Click to downloadKeep searches simple, eg. "belt" or "pump".
$7.30
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order now and your part arrives by Mar 20
In Stock
Order now and your part arrives by Mar 20
$130.18
This pressure regulator is three inches long. It is made of metal, but has a blue plastic plug on each end. This regulator sits below a gas range's control panel.
In Stock
Order now and your part arrives by Mar 20
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
In Stock
Order now and your part arrives by Mar 20
Special Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JGC8645ADW
Viewing 2 of 2Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marlene from Dana Point, CA
- Parts Used:
- WP7432P109-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we h
... Read more
ad to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith A. from Elizabeth, IL
- Parts Used:
- WP7103P178-60, 7507P241-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Treads on holder were stripped
Needed to remove all 4 burners to repair
one, but it went without a hitch.
Thanks to your exacting and clear diagrams, we were able to locate the correct parts
We called JennAire, but they were unable to
find the part..
It was delivered in a timely fashion and
we were able to finish the job in abo ... Read more ut
3 hours. thanks
one, but it went without a hitch.
Thanks to your exacting and clear diagrams, we were able to locate the correct parts
We called JennAire, but they were unable to
find the part..
It was delivered in a timely fashion and
we were able to finish the job in abo ... Read more ut
3 hours. thanks
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pleasanton, CA
- Parts Used:
- WP7432P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed
took the nuts off &replaced the new ignited
Was this instruction helpful to you?
Thank you for voting!