Models
>
JGA8100ADB
JGA8100ADB Jenn-Air Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGA8100ADB
Viewing 1 of 1Keep searches simple, eg. "belt" or "pump".
These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.
In Stock
Order within the next 7 hrs and your part ships today!
In Stock
Order within the next 7 hrs and your part ships today!
$158.44
This surface burner head is for ranges.
Surface burner head distributes the gas through holes or slots to create an even flame across the cooking area.
Shut off the gas supply and unplug the ran...
In Stock
Order within the next 7 hrs and your part ships today!
In Stock
Order within the next 7 hrs and your part ships today!
$8.04
This is the replacement brass seal for your range or cooktop. It is made of brass and is approximately 1 inch in diameter. This part may also be known as the surface burner orifice holder seal. It pre...
In Stock
Order within the next 7 hrs and your part ships today!
In Stock
Order within the next 7 hrs and your part ships today!
$177.47
This is one double burner grate - which means you get one grate that covers two burners.
In Stock
Order within the next 7 hrs and your part ships today!
In Stock
Order within the next 7 hrs and your part ships today!
$4.68
Sold individually. This screw is half of an inch long. It is made of metal and it is intended for use with some Maytag brand ranges.
Special Order
In Stock
Order within the next 7 hrs and your part ships today!
In Stock
Order within the next 7 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JGA8100ADB
Viewing 4 of 4Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Gas smell
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- roy from East Providence, RI
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t
... Read more
hat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joellen from Castro Valley, CA
- Parts Used:
- WP3403M075-10, 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Gas burner head on stove top rusted out producing blue flame where there shouldn't be
Removed stove top module and unscrewed the bottom panel. Burner head rotated out fairly easily. I ordered both the burner unit and the igniter just to be safe even though the old igniter still worked. I used the other module as a guide to reassemble the unit. The new burner head was little difficult to rotate back in and did not rotat
... Read more
e quite as far as the original so the gas pipe was just a fraction out of alignment but there is some flex so it worked out OK when it was re-installed. Everything worked perfectly when I turned on the burner and there are no gas leaks and no blue flames where there shouldn't be!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from Mooresville, NC
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
several grate pads fell out/lost /broke during cleaning
The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It i
... Read more
s available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive.
Read less
Was this instruction helpful to you?
Thank you for voting!