Models
>
JGC4430BDW14
JGC4430BDW14 Jenn-Air Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGC4430BDW14
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
In Stock
Order within the next 6 hrs and your part ships today!
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
$9.13
This part is the replacement grommet for your cooktop or range. It is made of black plastic and is approximately 1 ¼ inches in diameter. This part may also be known as the cooktop burner knob gasket, ...
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
Special Order
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
This grate is used for gas range/cooktop. Grate is sold individually. This is the grate that sits over the burner for your pots and pans to rest on while cooking.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anna from MONROVIA, CA
- Parts Used:
- WP7733P382-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My cooktop knob melted
I had used a pan too large for the middle burner - result: melted knob. Just pulled the old one off (up and straight) and then pushed the new one down firmly. Make sure the indicator line is pointing at you, so the flat side of the spindle matched the flat side of the hole on the knob. Easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from St. George, UT
- Parts Used:
- WP7518P465-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
black dirty burner grates
replaced grates
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAM from SAN DIEGO, CA
- Parts Used:
- WP7527P028-60, WP400021-1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No ignition
First I drilled out the screws on the burner as they were fused. I opened the stove top cover to access the underside of the burner. Removed the orifice holder, by disconnecting the gas line with a line Wrench and the electric cord.
The trick is to be careful with the gas line. Also when you go to replace the orifice holder ... Read more you will notice that the holes are not threaded. The metal is soft and you're supposed to just screw the screws into the holes and let them bite into the metal. Then you reattach the gas on the electric and put the stove top back together.
The trick is to be careful with the gas line. Also when you go to replace the orifice holder ... Read more you will notice that the holes are not threaded. The metal is soft and you're supposed to just screw the screws into the holes and let them bite into the metal. Then you reattach the gas on the electric and put the stove top back together.
Read less
Was this instruction helpful to you?
Thank you for voting!