Models
>
JGD3536BS00
JGD3536BS00 Jenn-Air Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGD3536BS00
Viewing 4 of 4Keep searches simple, eg. "belt" or "pump".
$41.57
This burner electrode, also known as a burner igniter, is a genuine OEM replacement part for your gas range. When the burner knob is depressed and turned, this part is used to create a spark that ligh...
In Stock
Order within the next 6 hrs and your part ships today!
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order within the next 6 hrs and your part ships today!
This is the burner head and electrode for your gas range. If your gas igniter glows but will not light, or if the element will not start or heat entirely, you may need to replace the burner head. This...
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
$92.66
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JGD3536BS00
Viewing 3 of 3Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from Lake Orion, MI
- Parts Used:
- WP74009336
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Ignitor stopped working on gas cooktop
As others reported, there are 2 torx screws that need to be removed so that the burner element can be removed. One came out with a little effort, the other one did not as it was corroded. After breaking a torx bit, a second torx bit succeeded in breaking off the screw head. This then required a drill to drill out the broken shaft and th
... Read more
en rethreading the screw hole. On to the ignitor replacement. The tiny screw holding the ignitor was corroded and would not come out. It too had to be drllled out and rethreaded. It was a 1/3" #4 screw with fine threads. Had to get it an appliance repair store as the local hardware places don't carry fine threaded screws. Finally got it all put back together after a week. My advice before ordering an ignitor is make sure you can take the current burner off the cooktop first to do the repair in the first place. BTW, the ignitor I ordered came quickly and was the correct part!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from San Luis Obispo, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ceramic insulator on the burner ignitor cracked & the spark shorted so that the burner would not ignite.
Firts I removed the 2 screws that held the burber in place. Then I lifted the burner up & disconnected the wire that connected to the ignitor. Then I removed the one screw that held the ignitor to the burner. I then reversed these steps, replacing the cracked ignitor with the new one, replaced the screw holding it to the burner, then reco
... Read more
nnected wire, returned the burner to the stove and replaced the two screws that held it. All Done!
Read less
Was this instruction helpful to you?
Thank you for voting!
electrode would not lite burner
Unscrewed burner head and replaced with new burnerhead and electrode. Just like new. Parts cost 128.00 including shipping. Very simple repair. Saved 200.00 in labor. Parts came within 36 hours. Super Fast.
Was this instruction helpful to you?
Thank you for voting!