CVG316W Jenn-Air Cooktop - Instructions

pulled old one out , cleaned the area & replaced with the new one.

Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.

Repair is simple as long as you TURN OFF THE CIRCUIT BREAKER first. After that, take off the cover over the switches (pull knobs off, remove 2 screws and lift off the cover), pull the bad switch straight up off the gas valve, pull the two wires off the switch, plug them back onto the new switch, place it back over the gas valve stem, reassimble the cover and knobs, turn back on the circuit breaker, and verify that ignition switch works. Not a hard repair. (HINT: while you are waiting on the replacement part, you can light the bad burner by turning on the opposite burner ignition switch and using that "spark" to light the other burner.)

Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.

Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.

Ordered new spark ignitors and plan to complete repair.

After waiting several years to replace rangetop knobs that had broken or melted at one time or another. I wasn't sure that the knobs i selected were correct & i needed them asap (house party). I called the # on the website & within 3 minutes placed an order that i was confident would work & had them overnighted!! I would definitely go to partselect again

I turned off the burner and allowed it to cool. I then checked the website for the part and also got a new grease filter and grill grate. When the parts came, I plugged in the new grill burner, replaced the grill grates, and dropped the filter in place. Total time was about 8 or 10 minutes--most of which was opening the packages. The grill burner is designed so that it can be removed and replaced with a standard 2 burner unit. No tools were needed. I was glad to find the parts for my 17 year old dual-fuel range.

-turned off power to stove
-lift off grill cover to downdraft
-remove 2 screws
-cut retaining clips with wire cutters
-remove old switch
-replace with new switch and push on new retaining clips
-remove and replace wires
-replace covers
-turn power back on

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 motor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net

removed 2 screws to access the ignitor. Discinnected the wires from the old ignitor and slid the old ignitor off. Installed the new ignitor and attached wires.

Since the other three burners sparked, I traced the problem to the switch on the valve shaft. To replace, (after unplugging the power cord) I pulled off the knobs, removed the two screws on the valve cover (inside the downdraft vent) and pulled the switch up the shaft to remove. I transferred the spade terminals to the replacement switch, oriented and installed.

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.