C200 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELOISE from MILFORD, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced filter
pulled old one out , cleaned the area & replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from fort pierce, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter that I actually did not know I had to change
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Carthage, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marion from aspen, CO
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Jenn-Air is an "antique." The filter was disgusting!
I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roe from Raleigh, NC
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Falling apart 20 year old grease filter for downdraft counter rangetop
Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from North Andover, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner had no temperature control other that full on.
Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).
Pull off the control knob.
Remove 2 screws that hold in control pannel.
Lift out the control pannel to the extent that the wires will let you. (2-3 inches)
Remove the nut that holds the switch/controller in the pannel.
Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.
Re-install the switch in the pannel.
Re-install the pannel in the stove.
Close breaker and test burner contol.
Pull off the control knob.
Remove 2 screws that hold in control pannel.
Lift out the control pannel to the extent that the wires will let you. (2-3 inches)
Remove the nut that holds the switch/controller in the pannel.
Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.
Re-install the switch in the pannel.
Re-install the pannel in the stove.
Close breaker and test burner contol.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from burke, AL
- Parts Used:
- WPY707454, WPY707453, WPY04100166, WPY04100165, 715878, 715877
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Wanted to update surface parts to a very old (27 yrs?) Jenn-air range on an island
The first task was to find the rings, drip bowls and elements on the "PartSelect" webpage. It was surprising easy, especially since I have no experience whatsoever in replacing range parts. The ordering was straight-forward, and most of the parts arrived within a week, a couple were back-ordered, but arrived a week later. Instillation was easy - just unplug elements, lift parts out, and insert new parts. I made a mistake in ordering - for the left side of the range, no adaptor rings are needed. I returned these excess parts to PartSelect, and within a week, they refunded the costs of these parts. Overall, I'm very please with the parts and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from Mattoon, IL
- Parts Used:
- WPY700854, WPY04100166, WPY04100165, 715878, 715877, 12001676
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
Wanted to "renew" cook top
The drip pans, burner knobs and electric surface elements are easily removed and replaced. The new receptacles for the burners were NOT easy to replace, but electricians were on hand to install when they replaced the cook top into the new counter top. Even the electricians had to read the instructions - and remove the control panel to replace one of the receptables. Looks like a new cook top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Poway, CA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lettering on old stove knobs was no longer visible and knobs were loose.
Took the old knobs off and replaced them with the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Chino, AL
- Parts Used:
- WP5701M122-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just ugly this time`
It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.
Was this instruction helpful to you?
Thank you for voting!
The drip bowls were old and stained; the knobs were so worn that they could hardly be read.
OK, this was easy, and it's a good thing 'cause I'm so blonde when it comes to repairs. But I will have to say this, my Jenn-Air looks like new and it is 29 years old. Thanks Partselect for making my repairs so quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Orange, CA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner was out but the burner coil worked on onother burner
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randy from manitou springs, CO
- Parts Used:
- 5708M016-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out heating element
part came quickly and fit perfect... everything works great...pretty simple repair... nice to have the right part and have it arrive so quickly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Beverly Hills, CA
- Parts Used:
- 715230K
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
bad element control switch
1. Turn off power to range at circuit breaker
2. Remove grate
3 Remove control knobs
4, Remove two screws holding control panel
5. With wrench, remove locking nuts from control switches
6. Lift panel, exposing switches
7. With new switch in hand, unattach old switch one terminal at a time, attaching new switch exactly as old switch, terminal by terminal.
8. Replace everything in reverse order
9.Turn on power
2. Remove grate
3 Remove control knobs
4, Remove two screws holding control panel
5. With wrench, remove locking nuts from control switches
6. Lift panel, exposing switches
7. With new switch in hand, unattach old switch one terminal at a time, attaching new switch exactly as old switch, terminal by terminal.
8. Replace everything in reverse order
9.Turn on power
Was this instruction helpful to you?
Thank you for voting!
the original equipment fan switch failed
The part we received from your supply store, a Maytag part, was in no way a direct replacement for the original Jenn-Air switch. I had to shave material carefully off all sides of the supplied switch, including the plastic flanges that were to hold the switch in place. Consequently, there was nothing left to hold the shaved-down switch in the opening. I had to rig two pieces of material to attach to the back of the switch to hold the switch, roughly, in place.
So, a poorly fitting replacement part that happens to function acceptably after an hour's work.
The repair: The balance of the repair was unremarkable. I simply removed the metal plate that the control knobs are mounted on, pulled it out of the rangetop, and removed the old switch. I snipped the wires, as your instructions said, nutting off the ground wire which is not used. I used a compression tool to attach the two wires to the quick-connect connectors you supplied (many home repair folks would not have a crimp tool for this job). The rest of the time was spent reshaping the switch you sent to fit into the too-small mounting hole.
I then simply returned the switch mounting plate, fastened with screws, to the range top.
So, a poorly fitting replacement part that happens to function acceptably after an hour's work.
The repair: The balance of the repair was unremarkable. I simply removed the metal plate that the control knobs are mounted on, pulled it out of the rangetop, and removed the old switch. I snipped the wires, as your instructions said, nutting off the ground wire which is not used. I used a compression tool to attach the two wires to the quick-connect connectors you supplied (many home repair folks would not have a crimp tool for this job). The rest of the time was spent reshaping the switch you sent to fit into the too-small mounting hole.
I then simply returned the switch mounting plate, fastened with screws, to the range top.
Was this instruction helpful to you?
Thank you for voting!