C202-C Jenn-Air Cooktop - Instructions

pulled old one out , cleaned the area & replaced with the new one.

Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

First I cut off power supply, removed screws that held panel on, pulled the switch up and disconnected wires. Installed new switch, being sure to connect wires in the correct places. Refastened panel to stove top. Turned power back on and tested switch and it Worked.

Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great!

It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.

Purchased 1 infinite switch and installed it on the left front burner. problem still there so I used the switch that I replaced on the rear burner and all was ok. The front switch had been sending full heat to the rear burner,but the problem ended up with the rear switch. The switches are interconnected and all are the same part number.Diagrams on partsselect were the key to a successful repair.To access the switch you need only to remove the fan cover, remove the 2 screws holding the switch assembly and move it foreward and then lift to reveal slide on connectors. Power to the unit is off at the main panel during the entire process.

Turned off power.

Removed two screws to free up section of cooktop containing 4 switches - 2 good, 2 damaged. Removed the dials from top of the 2 damaged switches. With an adjustable wrench, loosed nut on stem of switch that fastened switch to assembly. Noted which of the 5 wires on each switch went on which tab. Pulled off 5 wires on one switch, finished removing the nut and removed broken switch. Put in new switch, attached the nut, and replaced 5 wires in exactly the same position, Tightened nut. Replaced dial. Repeated procedure for second switch. Placed section containing the 4 switches back on cooktop and inserted/tighted 2 screws holding it in place.

Turned on power.

Told cleaning people to NEVER put aluminum foil under the burner units again. The foil shorted across the power and damaged the switches.

This was a piece of cake since the parts were a perfect replacement. I took the element apart and replaced the two receptacles by cutting the old wires and using the included wire nuts to splice the wires. The two switches were easily replaced by carefully connecting the wires like they were hooked up on the old switches. The indicator light was also easily replaced, although snapping the lens into place seemed to take a lot of force (I was afraid that I might break it). All in all, quite easy.

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

part came quickly and fit perfect... everything works great...pretty simple repair... nice to have the right part and have it arrive so quickly

I have bought several drip bowls over the years. They all seemed to not fit just right. These are perfect! Thanks!

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.