CCGP2820PR Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marlene from Dana Point, CA
- Parts Used:
- WP7432P109-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we had to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from Dallas, TX
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Simply needed a new knob, however...
However, I was very happily surprised how fast I got the part even though I did not specify fast shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from ESTERO, FL
- Parts Used:
- WP5700M611-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
drain jar lids rusted and broken of their mounts
The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Houston, TX
- Parts Used:
- WP7730P011-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Indicator Lens melted and fell back into the control panel
I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....
Was this instruction helpful to you?
Thank you for voting!
Griddle "infinite switch" bad and large burner gas valve
turn off gas,
disconnect gas line from stove
remove stove from countertop (gravity held it down - so don't bother pulling out a bunch of screws yet)
move to table
remove stove facia - 4 small screws
loosen large reverse pressure bolds (3/8 socket)
once the facia is removed - you will have access to all switches and gas burners.
the replacemnt of the two switches was simple.
reverse process to re install.
I had my 12 year old there to hold the stove up in a balanced position - it made it much easier - that third hand helps!
disconnect gas line from stove
remove stove from countertop (gravity held it down - so don't bother pulling out a bunch of screws yet)
move to table
remove stove facia - 4 small screws
loosen large reverse pressure bolds (3/8 socket)
once the facia is removed - you will have access to all switches and gas burners.
the replacemnt of the two switches was simple.
reverse process to re install.
I had my 12 year old there to hold the stove up in a balanced position - it made it much easier - that third hand helps!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Gladwyne, PA
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Housekeper broke knob several years ago and left that burner out of service.
I eventually searched online for a supplier and ordered the replacement knob. Ordering was easy and delievery was quick. Replacing the gas valve knob was easy; just slid it in place. Now all 4 burners are available for cooking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from COLUMBUS, OH
- Parts Used:
- WP71001057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knob broke on range
Simply removed old knob and popped on new knob. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Shawano, WI
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
Just had to push it into place, by hand only
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Mcdonough, GA
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed the knob for stove
Put it on simply as that thanks it was a perfect fit!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- darryl from everett, WA
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Gas Valve Knob for Jenn Aire Gas Stove
Slipped off old one and slipped on new one. The part was the right one and works great. Timely receival of part was great. Communication from you was great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pleasanton, CA
- Parts Used:
- WP7432P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed
took the nuts off &replaced the new ignited
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathryne from Marietta, GA
- Parts Used:
- 71003159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Griddle was scratched.
Removed old griddle and plugged in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Jefferson, MD
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken cooktop knob
Just slipped the new knob on with no problem. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diann from Wylie, TX
- Parts Used:
- WP7504P157-60, WP7432P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
The Igniters Would Spark Continually And Then One Burner Would Not Go On
Turned off gas, unscrewed nut that held on the plate unplugged the igniter and replaced it and put it back together, very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Awendaw, SC
- Parts Used:
- WP7504P157-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bad screw on cap
replace burner cap
Was this instruction helpful to you?
Thank you for voting!