Models
>
CCGX2620B
CCGX2620B Jenn-Air Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CCGX2620B
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
$26.40
This burner knob is two inches in diameter. It is a black knob with a white indicator dot. This knob is made entirely of plastic.
In Stock
On Order
In Stock
In Stock
$173.40
This pressure regulator is three inches long. It is made of metal, but has a blue plastic plug on each end. This regulator sits below a gas range's control panel.
In Stock
Special Order
This part helps the flame to spread for even heat. Also protects your burner head from spills.
No Longer Available
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for CCGX2620B
Viewing 2 of 2Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marlene from Dana Point, CA
- Parts Used:
- WP7432P109-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we h
... Read more
ad to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from Los Angeles, CA
- Parts Used:
- 71002776
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
two small burners were worn out
started with turning off gas and unplugging electric then removed right side of stove top that exposed burners removed plastic igniter switch from top of burner valve and in very tight area used 1/4" combo wrench to turn hex screw on underside of burner valve once broke loose the rest was easy just patients and a little determination remo
... Read more
ved and everything in reverse to install works fine
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mullica Hill, NJ
- Parts Used:
- 71002728, 71002727, WP7509P062-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
Conversion back to natural gas From propane
I converted the cooktop from propane to natural gas, the parts I was told I needed were the incorrect parts. I called because I was not sure about the listed parts. I was helped over the phone but recieved the LP parts. The flame was very low, and i found the orifices I replaced were the same parts I just took out.I contacted Parts sele
... Read more
ct and they were helpful and credited my purchase without any hestitation.Once the new orfices were recieved it was easy to install. I recommend using a nut driver with sticky tape to go the orifice holder after the venture is removed. You do not have to disassembe the stove as long as you don't drop the part. Changing the regulalor was also very easy by removing the gold nut and pulling the white pin out and flipping it over to Nat. The flat side of the pin is labeled LP or NAT. Then just screw the nut back in and tighten. The LP orifices are labeled on the side 0.65, 0.69, and 0.70 the natural gas orifces are colored black, silver , and red. It would be just as easy to go from Natural gas to LP!
Read less
Was this instruction helpful to you?
Thank you for voting!