Models
>
CVE4180S-C
CVE4180S-C Jenn-Air Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CVE4180S-C
Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
$27.76
This is a genuine OEM replacement grease filter for downdraft exhaust ranges and cooktops. The filter is used to trap grease and particles that result from cooking and will need to be replaced once th...
In Stock
Order now and your part arrives by Mar 26
$11.50
This chrome-colored drip bowl is a genuine OEM part for your range. This bowl fits underneath the 8-inch burner elements and is sold individually. The drip bowl is used to catch any spills that result...
In Stock
Order now and your part arrives by Mar 26
$10.45
This part includes one OEM chrome-colored 6-inch drip bowl for an electric range. This part is responsible for catching spills from cookware placed on the burner, so it is susceptible to tough stains ...
In Stock
Order now and your part arrives by Mar 26
$20.95
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
In Stock
Order now and your part arrives by Mar 26
$76.45
This surface burner switch, also known as an infinite switch, controls the heat level of stovetop burners. When you turn the knob, the switch adjusts the power to the burner for precise temperature co...
In Stock
Order now and your part arrives by Mar 26
$7.30
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order now and your part arrives by Mar 26
This 8 inch surface burner with reinforced delta frame carries 2100 watts and 240 volts. It has five turns and is compatible with many electric ranges. Its center medallion is all black in color.
In Stock
Order now and your part arrives by Mar 26
This 6-inch coil surface element is designed to replace a broken burner on compatible electric ranges, restoring direct heat for everyday cooking. With a power output of 1250 watts, it efficiently hea...
In Stock
Order now and your part arrives by Mar 26
$26.73
Sold individually. This surface burner knob is a little under two inches in diameter. It is a black knob with gray numbering indicating the temperature level of the surface burner. Made entirely of pl...
In Stock
Order now and your part arrives by Mar 26
$12.55
This cartridge assembly male contact spade is made of metal. These are sold individually, though each range uses four contact spades.
In Stock
Order now and your part arrives by Mar 26
Special Order
This part is used as a support for the grill element. Sold individually.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for CVE4180S-C
Viewing 4 of 4Element will not heat
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Oven is too hot
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELOISE from MILFORD, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced filter
pulled old one out , cleaned the area & replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from fort pierce, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter that I actually did not know I had to change
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James H from Oxford, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner had one temperature--hot, regardless of setting
1. Killed power and removed the regulator's knob, noted the position of the old control.
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in ... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in ... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
Read less
Was this instruction helpful to you?
Thank you for voting!