Models > CCG2423W

CCG2423W Jenn-Air Cooktop

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for CCG2423W

Viewing 3 of 3
BODY Diagram and Parts List for Jenn-Air Cooktop
BODY
TOP ASSEMBLY Diagram and Parts List for Jenn-Air Cooktop
TOP ASSEMBLY
WIRING INFORMATION Diagram and Parts List for Jenn-Air Cooktop
WIRING INFORMATION
Keep searches simple, eg. "belt" or "pump".
Dryer Screw – Part Number: WP90767
$7.30
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order now and your part arrives by Mar 19
REGULATOR – Part Number: W11106948
$130.18
This pressure regulator is three inches long. It is made of metal, but has a blue plastic plug on each end. This regulator sits below a gas range's control panel.
In Stock
Order now and your part arrives by Mar 19
Valve Screw – Part Number: W10491986
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
Burner Foam Tape – Part Number: 12400021
No Longer Available
Spark Module – Part Number: WPY705823
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for CCG2423W

Viewing 2 of 2
Will Not Start
Fixed by these parts
Fixing
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Marlene from Dana Point, CA
Parts Used:
WP7432P109-60
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we h ad to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Read less
12 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from CARSON CITY, NV
Parts Used:
WPY705823
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The Spark function just quit working.
The instructions on the website made it real easy to remove & Replace with a new module. Thanks for your Part & Install instructions.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Pleasanton, CA
Parts Used:
WP7432P109-60
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench set
As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed
took the nuts off &replaced the new ignited
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More