2370EGS Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELOISE from MILFORD, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced filter
pulled old one out , cleaned the area & replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from fort pierce, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter that I actually did not know I had to change
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marion from aspen, CO
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Jenn-Air is an "antique." The filter was disgusting!
I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roe from Raleigh, NC
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Falling apart 20 year old grease filter for downdraft counter rangetop
Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from North Andover, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner had no temperature control other that full on.
Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).
Pull off the control knob.
Remove 2 screws that hold in control pannel.
Lift out the control pannel to the extent that the wires will let you. (2-3 inches)
Remove the nut that holds the switch/controller in the pannel.
Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.
Re-install the switch in the pannel.
Re-install the pannel in the stove.
Close breaker and test burner contol.
Pull off the control knob.
Remove 2 screws that hold in control pannel.
Lift out the control pannel to the extent that the wires will let you. (2-3 inches)
Remove the nut that holds the switch/controller in the pannel.
Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.
Re-install the switch in the pannel.
Re-install the pannel in the stove.
Close breaker and test burner contol.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Poway, CA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lettering on old stove knobs was no longer visible and knobs were loose.
Took the old knobs off and replaced them with the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Chino, AL
- Parts Used:
- WP5701M122-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just ugly this time`
It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from baltimore, MD
- Parts Used:
- WP179051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing screws for oven door
After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Beverly Hills, CA
- Parts Used:
- 715230K
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
bad element control switch
1. Turn off power to range at circuit breaker
2. Remove grate
3 Remove control knobs
4, Remove two screws holding control panel
5. With wrench, remove locking nuts from control switches
6. Lift panel, exposing switches
7. With new switch in hand, unattach old switch one terminal at a time, attaching new switch exactly as old switch, terminal by terminal.
8. Replace everything in reverse order
9.Turn on power
2. Remove grate
3 Remove control knobs
4, Remove two screws holding control panel
5. With wrench, remove locking nuts from control switches
6. Lift panel, exposing switches
7. With new switch in hand, unattach old switch one terminal at a time, attaching new switch exactly as old switch, terminal by terminal.
8. Replace everything in reverse order
9.Turn on power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeannine from Twentynine Palms, CA
- Parts Used:
- 700855K
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old switch had burned out and needed to be replaced
Turned off electricity at the circuit box. Removed four screws from panel cover that housed the switch. disconected the wires from the old switch and replaced the old switch with the new one reconected the wires put the panel cover back on. voila done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- catherine from holland, MA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knobs were old could not read numbers
knobs fit perfectly
Was this instruction helpful to you?
Thank you for voting!
Switches were worn out (2) and shorting out. Throwing the breaker. Actually I think the ladies boyfriend/ fiance' tried to replace the knobs that were broken with universal knobs. They didn't fit so he forced them and broke the switches internally.
Shut off the breaker! Removed down draft grill. Removed two phillips head screws and lifited switch plate out. Removed switches (2) and made wiring diagram as I went. Looked up Jenn-Air on line and ordered parts. Lost wirihng diagram in the process but still had two switches wired . Replaced all four switches. Everything working great. However while I was waiting on switches to arrive, somebody at the house was fooling with the switch plate and broke the on red indicater lens so now I'm ordering that. Oh well....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAY from DANBURY, CT
- Parts Used:
- 12001418
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Exhaust-fan switch didn't work any more.
FIRST OPENED THE CIRCUIT BREAKER. Snipped the three wires, capped the white one with the ceramic insulating nut and crimped the spade connectors to the other two. Then CAREFULLY filed one side of the rectangular hole in the escutcheon until iwas wide enough to accept the new swich. Drew the two wires up through the hole, attached them to the switch and pushed the switch into the hole until it snapped in place. Reseated the escutcheon and reconnected the two screws. Closed the circuit breaker, pressed the switch and VOILA, on went the fan. Be careful not to let filings fall into the electrical stuff. Need crimping tool & file.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from LAKE GROVE, NY
- Parts Used:
- WP71003558, WP707929, 715957K
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Downdraft Motor Bearings Shot
I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 motor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Palo Alto, CA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Burner temperature control did not work.
Got a no-name tailor-it-yourself replacement switch from a San Jose, CA appliance parts store; but the switch was so cheaply made that it fell apart when I tested it.
Got a RobertShaw part from PartSelect and now the burner works perfectly.
Got a RobertShaw part from PartSelect and now the burner works perfectly.
Was this instruction helpful to you?
Thank you for voting!