PP975WM1WW General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from LAUREL, MD
- Parts Used:
- WB23T10023
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Lightning strike blew out my GE cooktop
Wife said cooktop was not working. I cut power and dropped the cover on the electronics box under the burners and could see it was burnt up. Looked like it would be hard to fix so I ordered a new cooktop. However, they couldn't place order until they measured - and that would not be for a week. So, I thought I would order the circuit board to see if I could replace it. Parts Select had good links to appliance parts so ordering was easy. Needed help to pull out the cooktop and flip it over but switching in the new board was relatively easy although there were lots of connectors to keep straight. Turned it on and it worked like new and cancelled order. Saved $1300 and was a hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Perryton, TX
- Parts Used:
- WB30T10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove Top Element Heat Varies
Removed stove top from counter, removed glass top by removing 10 phillps screws, removed control bracked, unplugged connectors(wires) on old control and plugged into the correct position on the new control, replace control on the bracket then reinstalled the stove top and placed the stove top back into counter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Manchester, MD
- Parts Used:
- WB30T10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Small Element on cook top fails to function
Turned of the electric at the circuit breaker. Removed the cable clamps for the electric feed cable to enable free movement of cooktop. Lifted cooktop from the counter and propped up on counter ledge. Removed control knobs. Removed perimeter screws, 8 phillips, from around the edge of the cook top surface where it attaches to the sheet metal housing and lifted glass top off. Removed the failed burner and disconnected the four electrical leads. Removed the mounting tabs from the old burner and installed them on the new burner. Attached the electrical leads to the new burner and tightened with pliers. Reattached glass top and knobs, reinstalled in counter, clamped the electrical cable, flipped the breaker and tested. All good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony g from MOUNT PLEASANT, SC
- Parts Used:
- WB30T10043
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
needed burner replacement
There are 18 sheetmetal screws not 8
The GE SREWS HAVE AN INTEGRATED WASHER which causes the philips head to STRIP these needed to be drilled out!!!
The glass top was GLUED to the sheetmetal box and did not come off without a fight
The GE SREWS HAVE AN INTEGRATED WASHER which causes the philips head to STRIP these needed to be drilled out!!!
The glass top was GLUED to the sheetmetal box and did not come off without a fight
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Marco Island, FL
- Parts Used:
- WB30T10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Haliant element was not heating
Take off the two small screws under the glass top. Use a nut driver or small Cresent wrench. Prop up or have somone hold the top up while you remove the old element and make sure you mark where the two clips that hold it to the top are located. Now disconnected the wires and attached them to the new element. My suggestion is to take off only one wire at a time and attach it to the new unit. A very easy fix. Not more than a 15- 30 minute effort.
Was this instruction helpful to you?
Thank you for voting!