JGP960SEA1SS General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Bloomsbury, NJ
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Bakersfield, CA
- Parts Used:
- WB31T10006, WB29K47, WB29K44, WB29K41
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My wife wanted different color stove top grate & burner caps.
Called GE for part number crossover from gray to black and asked for an email quote. Called Parts Select for pricing, which was alot lower! Shipping took five days and less then $8.00 buck....now mama's happy!!!! Thanks for great frendly service from Mike in California.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aloha from Monterey, LA
- Parts Used:
- WB28K145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacement cook-top, had natural gas orifices, needed propane
Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Irvine, KY
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode ceramic insulator was cracked
First I elevated range top, then removed cracked electride from connector pin. Installed new electrode and lowered range top and all was fine.
Was this instruction helpful to you?
Thank you for voting!
No ignition
replace parts and plug in wire harness as you go.....clean up old seal area on burner bowl and stove top...install new seals.....done.....saved $400 in repair labor or $1200 for new stove top.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LORDSBURG, NM
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
No Spin Cycle
Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wally from lake oswego, OR
- Parts Used:
- WB24K5078
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Failed ignition switch
took me a a while to find my problem. One burner would not spark to ignite gas burner. From Part Select website I noticed the part that was the problem from the parts diagram. I did not realize it was related to ignition until I saw that. Easy and cheap to fix after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Dills burg, PA
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Heating element quit working after 30 years
Removed several screws and removed element. Replaced same. Total ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Carlsbad, CA
- Parts Used:
- WB3K5310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs on gas counter top
I was washing the knob on my gas counter tops and broke 2 of them. I had to order 2 new ones. I will be very careful from now on with my removing them to be washed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irish from Stockbridge, GA
- Parts Used:
- WB3K5310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner knob broke
The repair was simple and easy. The ordering process with PartSelect was equally easy and painless. I would order with them again if the need arised.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimiego from San Diego, CA
- Parts Used:
- WB24K5083
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burner would not light
replaced switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Longmont, CO
- Parts Used:
- WB13K18
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
would not ignite
It was so easy.I removed the old part with the new with pliers. Voila/// it worked.
Was this instruction helpful to you?
Thank you for voting!
rebuilt stove top back to new condition
took cook top out for new counters and stipped cooktop down to bassic parts. cleaned everything and reassembled with new parts and paints.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Laguna Hills, CA
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Left rear burner would not light
Began by removing the front panel where the range handles are located. There were 7 screws located under the panel which required opening of the oven hood. All of this removal was a waste of time, because the range top was on hindges. The only thing holding ithe range top down was the accumulated grease and oil along the edges. I used a screwdriver to sperate the range panel. There were side supports to hold the the top up, like a car hood support. Replacing the electrode was a snap after that. Overall, it took less than 30 mins but it would have taken less than 10 if I hadn't removed the front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Jenison, MI
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no spark at burner
Remove grates,pans and disk. Remove allen screws at each burner. Take a flat blade screwdriver and press in on tabs on each side of front of stove to depress keepers and lift top up. Remove wire, and keeper on bottom of electrode. Reverse for install.
Was this instruction helpful to you?
Thank you for voting!