Models
>
PP989TN2WW
PP989TN2WW General Electric Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for PP989TN2WW
Viewing 1 of 1
Manuals & Guides for PP989TN2WW
Click to downloadKeep searches simple, eg. "belt" or "pump".
In Stock
Order within the next 11 hrs and your part ships today!
$56.66
This part is the replacement fan switch or downdraft vent fan knob for your range hood. It measures approximately 2 inches by 1 inch. The fan switch allows you to turn on the range hood fan when it is...
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Prem from WOODBURY, CT
- Parts Used:
- WB24X10174
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Broken shaft on downdraft speed switch
The controls are on the glasstop and no way to access them from below, so the glass top has to be removed by removing any straps/braces from below and raising the rangetop housing above the counter height.
The foil tape connecting to the downdraft ductwork will need to be removed. Make sure you have foil tape to reseal this co ... Read more nnection.
The black foam tape between the cooktop housing and the countertop will need to be separated with a putty knife. Be sure to have the 1/4” low density foam tape on hand for replacement.
Remove the 6 knobs by lifting them upward and then lift the housing above counter height.
The loosened housing can be supported by two pieces of 1x2 that straddle the opening. The sheet metal screws around the perimeter are easily removed and a putty knife under the glass should release the glass. Once the glass is removed, you’ll see an electrical control box with the 6 switches. The fan switch is held in place with two screws. The switch can then be accessed from the side and replaced. Just note the 4 colored wires and move them to the new switch. There’s a 5th contact that’s unused.
Reassembly is straightforward but you’ll need to remove any remaining foam tape, clean the underside and the countertop before applying the new tape.
The foil tape connecting to the downdraft ductwork will need to be removed. Make sure you have foil tape to reseal this co ... Read more nnection.
The black foam tape between the cooktop housing and the countertop will need to be separated with a putty knife. Be sure to have the 1/4” low density foam tape on hand for replacement.
Remove the 6 knobs by lifting them upward and then lift the housing above counter height.
The loosened housing can be supported by two pieces of 1x2 that straddle the opening. The sheet metal screws around the perimeter are easily removed and a putty knife under the glass should release the glass. Once the glass is removed, you’ll see an electrical control box with the 6 switches. The fan switch is held in place with two screws. The switch can then be accessed from the side and replaced. Just note the 4 colored wires and move them to the new switch. There’s a 5th contact that’s unused.
Reassembly is straightforward but you’ll need to remove any remaining foam tape, clean the underside and the countertop before applying the new tape.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from Grand River, IA
- Parts Used:
- WB03T10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fan knob was loose due to the metal insert being missing
Removed the knob and replaced it with the new knob. Didn't even break a sweat!
Was this instruction helpful to you?
Thank you for voting!