JGP933WEC1WW General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Logansport, IN
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Top four burners on oven would not light without using match
Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. There are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Star City, AR
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Foot had worn out
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Maurertown, VA
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Spark was present in only two of four burners
Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Villa Park, IL
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
stove top burner ignition spark progressively got weaker and then stopped on all but one burner.
I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Jacksonville, FL
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chadd from philadelphia, PA
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
2 burners wouldnt spark
Took top off, removed wires from old spark module and put them on new one. Very easy and quick, works very well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Freehold, NJ
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Only one burner sparking on range.
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from NASHVILLE, TN
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced igniter pins but no joy, needed igniter module
Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry L from Puyallup, WA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from new hope, PA
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burners began to fail to ignite.
Removed six screws on the back panel. Just switched six wires from the old to the new module. Stove burners work perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Stratham, NH
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
I do use silicone to help hold the foot but it still won't hold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David A from Spring, TX
- Parts Used:
- WB04T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner would not light because spark was skiping to ground elsewhere
First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. I used new gashket and ignitor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Washington, NC
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range burners would not light
Lift up work light cover. Remove lamp. Remove two screws from control panel. Lift up control panel. Pop out spark module from slots. Remove the 6 wires from module. Attach wires to new module - module has a diagram on it that shows where wires are attached. Push new module back into slots. Replace control panel cover, lamp, and work light. Now the burners light - the spark is MUCH stronger than before repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from NEPTUNE, NJ
- Parts Used:
- WB28T10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Burner injet replacement
I needed a right front burner injet which is no longer made. On my cooktop I was able to move the left burner to the right and then ordered the left. Very easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!