JGP970KEK1CC General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Freehold, NJ
- Parts Used:
- WB13X27058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner wouldn't light
I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair.
I've replaced 2 igniters on this stove. My symptoms were that when I tried to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.
I've replaced 2 igniters on this stove. My symptoms were that when I tried to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Star City, AR
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Foot had worn out
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from HERNDON, VA
- Parts Used:
- WB13X27058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replacing Spark Igniter
Pulled the old one out. Disconnected the wire. Repaired the frayed wire cover with Liquid Tape. Connected the wire. Inserted the new part into the hole. This is after installing a new spark module earlier. But that was dumb easy too. So for about $100 bucks in parts and an hour of my time I saved myself the appliance repairman money and agonizing scheduling and dealing with them for the price of gold. I also replaced all the gaskets on the burners in that time. It so easy even a financial planner could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Stafford, VA
- Parts Used:
- WB13X27058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One burner would not light without using a match
I removed the burner head #152 and the Burner Cap #330, no tools are needed to remove these items. I pulled the igniter up far enough to get to the wire, disconnected and connected the new igniter put it back in place, reassembled the two parts plugged it back in and turned it on and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Jacksonville, FL
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Stratham, NH
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
I do use silicone to help hold the foot but it still won't hold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David A from Spring, TX
- Parts Used:
- WB04T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner would not light because spark was skiping to ground elsewhere
First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. I used new gashket and ignitor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry L from Puyallup, WA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NORTHFORD, CT
- Parts Used:
- WB03T10093
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original knob broke that changed the burner size.
Just had to put the new knob on the shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Austin, TX
- Parts Used:
- WB13X27058
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replacing ignitor
Got ignitor and it did not have wire attached as shown in the picture of parts. However, all I did was take burner cap off, and gently life ignitor up and out, detach the wire, attach new ignitor to wire and reset.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from HENDERSONVLLE, NC
- Parts Used:
- WB02T10461
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Broadalbin, NY
- Parts Used:
- WB02T10461
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
The Grate foot is to big for the hole.
I had to drill the hole to a larger size to enable the foot to fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from CYPRESS, TX
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very easy
there were no grate pads so it was easy to add them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chelagh from Fredericksburg, VA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
Nothing technical.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tijeras, NM
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate foot bdroke off allowing grate to scratch cooktop
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this instruction helpful to you?
Thank you for voting!