JGP5036DL3BB General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Irene H from HENRICO, VA
- Parts Used:
- WB02X24790
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing grate foot / bumper
Put in a new foot / bumper. That's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitzi from Briarcliff Manor, NY
- Parts Used:
- WB28K10222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard B from CLARKSBORO, NJ
- Parts Used:
- WB28K10222
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Large burner cap finish was damaged
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from NAPLES, FL
- Parts Used:
- WB13X29294
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Electrode would produce spark to lite burner
The following are steps in replacing a burner electrode for GE Profile Cook Top Model PGP7030DL1BB
1. Shut off gas and unplug electrical plug
2. Remove all stove grates and turn on knobs
3. Remove all burner covers
4. Remove all screws [three for each burner]
5. Remove two screws near front by removing rubber grate grommets
6. Carefully Lift off stove cover and set aside
7. Remove shield near back of stove top. This exposes all burner wires
8. Remove electrode to burner which does not lite by sliding out clip at bottom of electrode—note color code of wire and replace with same. Change one electrode at a time to insure wire color code is correct.
9. Reassemble in reverse order of steps 1-8
HAVE A NICE DAY
1. Shut off gas and unplug electrical plug
2. Remove all stove grates and turn on knobs
3. Remove all burner covers
4. Remove all screws [three for each burner]
5. Remove two screws near front by removing rubber grate grommets
6. Carefully Lift off stove cover and set aside
7. Remove shield near back of stove top. This exposes all burner wires
8. Remove electrode to burner which does not lite by sliding out clip at bottom of electrode—note color code of wire and replace with same. Change one electrode at a time to insure wire color code is correct.
9. Reassemble in reverse order of steps 1-8
HAVE A NICE DAY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from PASADENA, TX
- Parts Used:
- WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Was this instruction helpful to you?
Thank you for voting!