Models
>
JGP933SEC2SS
JGP933SEC2SS General Electric Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGP933SEC2SS
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
$12.51
Sourced directly from the manufacturer, this OEM replacement grate foot is for ranges and cooktops. The grate foot attaches to the bottom of the burner grate to prevent the cooktop from being scratche...
In Stock
In Stock
$63.66
Also known as spark electrode. This part helps your burner ignite and produce flame.
In Stock
In Stock
This part is the spark igniter switch and harness assembly for your gas range. This harness assembly has 4 igniter switches already wired into it. It includes the igniter switches and the complete wir...
No Longer Available
In Stock
On Order
$63.33
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
In Stock
$54.42
This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane.
This valve automatically cuts off the flow of gas at a certain pressure.
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JGP933SEC2SS
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Freehold, NJ
- Parts Used:
- WB13X27058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner wouldn't light
I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair.
I've replaced 2 igniters on this stove. My symptoms were that when I tried ... Read more to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.
I've replaced 2 igniters on this stove. My symptoms were that when I tried ... Read more to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Star City, AR
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Foot had worn out
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Stony Brook, NY
- Parts Used:
- WB18T10339
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
No click or ignition after turning on burner - had to replace Ignitor Switch assembly
Do not remove the gas line.
Take off the burner racks and burner covers
Gently extract/remove the ignitors from each burner. You may have to use pliers, but be careful. They are ceramic.
Once you pull out the ignitors, you can remove the ignitors from their wires using plyers, you may have to twist them a ... Read more little.
To take off the top - use Star screw drivers to remove the burners
Remove all the burners.
The star screws, and the burners are the only thing holding the top on.
Take off the steel top.
That exposes the ignitor switch assembly.
Make sure you follow the positioning diagram that comes with the new part.
Thats it really.
I removed the gas, because I thought I had to, but you don't need to. You can do the whole job in 30 minutes if you are careful.
Hope it helps.
You'll have to
Take off the burner racks and burner covers
Gently extract/remove the ignitors from each burner. You may have to use pliers, but be careful. They are ceramic.
Once you pull out the ignitors, you can remove the ignitors from their wires using plyers, you may have to twist them a ... Read more little.
To take off the top - use Star screw drivers to remove the burners
Remove all the burners.
The star screws, and the burners are the only thing holding the top on.
Take off the steel top.
That exposes the ignitor switch assembly.
Make sure you follow the positioning diagram that comes with the new part.
Thats it really.
I removed the gas, because I thought I had to, but you don't need to. You can do the whole job in 30 minutes if you are careful.
Hope it helps.
You'll have to
Read less
Was this instruction helpful to you?
Thank you for voting!