Models
>
FFEC3005USA
FFEC3005USA Frigidaire Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for FFEC3005USA
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
$12.59
This OEM drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. Drip bowls catch any spills, and are a quick, easy, and cheap way to improve your cooktop aesthetic....
In Stock
$7.46
This drip bowl is an OEM approved replacement part designed for use with various electric ranges and cooktops. This part is located underneath the burner to contain any spills while cooking. It fits ...
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
Special Order
In Stock
Special Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for FFEC3005USA
Viewing 1 of 1Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Herrick, IL
- Parts Used:
- 318293827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner would consistantly go to high no matter where the dial was positioned.
First I unplugged the stove.Removed the upper control panel back (10 phillips screws). Removed the plastic dial( pulls straight off). Removed the 2 screws behind the dial that is holding the switch in the control panel. Took one wire at a time off the old switch and put them on the new switch according to each electrical spade marking. L1
... Read more
, L2, H1, H2 and P. Installed the new switch in the control panel securing it with the 2 screws. Installed the dial, installed the upper back panel using the old screws. Plugged the stove back in and tested it.
Note: My new switches shaft was 1/8 of an inch longer so it does put the dial a little further away from the control panel. Wife says: It's OK, don't worry about it.
Note: My new switches shaft was 1/8 of an inch longer so it does put the dial a little further away from the control panel. Wife says: It's OK, don't worry about it.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Lafayette, GA
- Parts Used:
- 318293827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One of the switches on my stove had quit exept for High. every level on the switch was high.
First I removed the 2 screws that held it in place.
Then I took te screws out of the backguard cover and pulled it down so that I would get to it. Then I unplugged the wires, and replugged them on the new switch, then screwed it back in to the range, then put all the screws back in backguard cover, and plugged the range back up and p ... Read more ut it back in its place. It was real easy.
Then I took te screws out of the backguard cover and pulled it down so that I would get to it. Then I unplugged the wires, and replugged them on the new switch, then screwed it back in to the range, then put all the screws back in backguard cover, and plugged the range back up and p ... Read more ut it back in its place. It was real easy.
Read less
Was this instruction helpful to you?
Thank you for voting!
Needed new drip bowls.
Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.
I was extremely pleased with the very quick delivery of needed parts.
I was extremely pleased with the very quick delivery of needed parts.
Was this instruction helpful to you?
Thank you for voting!