FFEC3005UBA Frigidaire Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Herrick, IL
- Parts Used:
- 318293827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner would consistantly go to high no matter where the dial was positioned.
First I unplugged the stove.Removed the upper control panel back (10 phillips screws). Removed the plastic dial( pulls straight off). Removed the 2 screws behind the dial that is holding the switch in the control panel. Took one wire at a time off the old switch and put them on the new switch according to each electrical spade marking. L1, L2, H1, H2 and P. Installed the new switch in the control panel securing it with the 2 screws. Installed the dial, installed the upper back panel using the old screws. Plugged the stove back in and tested it.
Note: My new switches shaft was 1/8 of an inch longer so it does put the dial a little further away from the control panel. Wife says: It's OK, don't worry about it.
Note: My new switches shaft was 1/8 of an inch longer so it does put the dial a little further away from the control panel. Wife says: It's OK, don't worry about it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Lafayette, GA
- Parts Used:
- 318293827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One of the switches on my stove had quit exept for High. every level on the switch was high.
First I removed the 2 screws that held it in place.
Then I took te screws out of the backguard cover and pulled it down so that I would get to it. Then I unplugged the wires, and replugged them on the new switch, then screwed it back in to the range, then put all the screws back in backguard cover, and plugged the range back up and put it back in its place. It was real easy.
Then I took te screws out of the backguard cover and pulled it down so that I would get to it. Then I unplugged the wires, and replugged them on the new switch, then screwed it back in to the range, then put all the screws back in backguard cover, and plugged the range back up and put it back in its place. It was real easy.
Was this instruction helpful to you?
Thank you for voting!
Needed new drip bowls.
Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.
I was extremely pleased with the very quick delivery of needed parts.
I was extremely pleased with the very quick delivery of needed parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from St. Albans, ME
- Parts Used:
- 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Couldn't find replacement trays locally. Part Select was very helpful and prompt in shipping.
Just placed the chrome bowl trays in place and was good to go. They look very nice.
Was this instruction helpful to you?
Thank you for voting!
Drip bowels needed to be replaced
I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from BRIMFIELD, MA
- Parts Used:
- 318293827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burner was sparking
Turned off electricity to the stove top opened up the aluminum cover under the stove top with the screwdriver Took off the wires one at a time with the pliers as they were on tight and replaced them on the new part Replaced the aluminum cover Turned on electricity and voila it worked fine no sparking
Was this instruction helpful to you?
Thank you for voting!
Pulled the heating element on each burner installed the drip pans.
They fit perfectly for this stove. I had bought some drip pans but definitely not the correct pan. Saved time and about same at stores price. Great service thank you will order elements next. Pull heating elements remove drip pans and replace with new pans ,replace heating element. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josephine from Malden, MA
- Parts Used:
- 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pitted, Eroded Drip Pans
1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.
Was this instruction helpful to you?
Thank you for voting!
Renewed drip pans
Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Arena, WI
- Parts Used:
- 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip Bowl Replacement
I could not find the larger size universal drip bowl to fit the 8" burners on my stove. This product replacement is perfect.
Was this instruction helpful to you?
Thank you for voting!
Couldn't find drip pans that fit
I went to all of the do-it yourself stores and spent a bunch of money on aftermarket drip pans only to find out that none of them fit. I came up on your website and also called customer service. The found the right part and mailed it too me. They fit perfectly. No more burnt and rusty drip pans. I know where to go for parts now.
Was this instruction helpful to you?
Thank you for voting!
Replace ill-fitting drip pans
After two failed attempts to get the 'correct' drip pans for my range from two other supply outlets, Part Select had the proper drip pans for this model. They fit perfectly! Simple installation and threw away those cheap, poorly fitting replacement pans I've put up with for three years! Thanks Part Select for having the correct parts!!
Was this instruction helpful to you?
Thank you for voting!