Models
>
CRG0860AAL
CRG0860AAL Crosley Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CRG0860AAL
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
This is a black burner head with the spark electrode.
NOTE: This part has been updated and there is no longer a gasket seal required.
In Stock
Special Order
$79.57
This switch is used with gas ranges and ovens. The part sits on top of the valve. Once the knob is turned it will create a spark that will light the gas and starts the burner.
In Stock
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
$14.09
This is a genuine OEM replacement part. This nut is used in a number of appliances. Most often it can be found in the assembly of ranges, air conditioners, cook tops, washers, microwave oven combos, r...
Special Order
Special Order
$106.04
This square burner grate has sides measuring approximately nine inches. It is all black in color.
In Stock
This valve can be used for the left rear or the right front burner.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for CRG0860AAL
Viewing 4 of 4Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Gas smell
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Herb from Sumas, WA
- Parts Used:
- WP7403P287-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
One burner was not igniting .. no clicking sound .. no spark.
On this range, the switch at any one burner causes the igniters to spark on all four burners. However, there was no spark anywhere when I turned the knob for the front right burner. This indicated a fault in the switch on that knob. Very important to start by unpluging the power cord (I got zapped trying to skip that part!) Then remov
... Read more
e all four burners, by turning them counterclockwise and lifting. Remove all igniter wires and set the burners aside. At the edge of each of the burner holes is a screw. Remove all four of these screws, then you can pry the cooktop up and remove it. Pull all four knobs off, and remove the four screws attaching the cover behind the knobs (two on top and two below (above oven door). This exposes the igniter switches. Slide the broken switch off the shaft, and remove the wires. (There is a small release tab at each pole of the switch. Depress it with a small screw driver and the wires can be pulled out.) Push the wires into the new switch, slide it into place, and put everything back together. Solved my problem!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yury from Brooklyn, NY
- Parts Used:
- WP3412D024-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner wouldn't start
Make a quarter turn counterclockwise, disengage a burner head, disconnect 2 wires, connect to a new head, install turn clockwise.
That's it!
That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Somerville, TN
- Parts Used:
- WP3412D024-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner head was rusted out. ordered 1 to see if part was correct. ordered 4 more to finish job.
unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.
Was this instruction helpful to you?
Thank you for voting!