Models > RTP308UWW-P1142505NW

RTP308UWW-P1142505NW Caloric Cooktop

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for RTP308UWW-P1142505NW

Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
This OEM replacement part has been sourced from the manufacturer. This spark ignition module is designed for use with ranges and cooktops. The spark ignition module works to provide the spark require...
No Longer Available
$7.91
Sold individually.
In Stock
$13.45
This screw is sold individually.
In Stock
This burner ignition switch is a little over an inch long. It is made of plastic and has a white center cam. This switch has some metallic components.
No Longer Available
This clip is well under an inch in diameter. It is made of metal and it will help secure a range's electrode.
No Longer Available
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
Nut
$14.08
This is a genuine OEM replacement part. This nut is used in a number of appliances. Most often it can be found in the assembly of ranges, air conditioners, cook tops, washers, microwave oven combos, r...
Special Order
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for RTP308UWW-P1142505NW

Viewing 3 of 3
Will Not Start
Fixed by these parts
Fixing
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
Fixing
How to fix it
Element will not heat
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
John from Alexandria, VA
Parts Used:
32020101
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 4 burners wouldn't light
Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each) and disconnecting electrode wires as I pulled them out, removed the stove top, unscrewed the old module, removed the 6 wires, connected wires to the new module, screwed it into place, reinstalled the top while poking the electrode wires through the top one by one, put the stove top in place, connected the wires to the burner discs. Done, and it works! It took longer to find and order the part than it did to change it out.
25 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from Schaghticoke, NY
Parts Used:
WPY0300521
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
pre- igniter went bad. No spark
The trick with any appliance is to remove all the extras,before you get to the problem.Considering that it has electricity, the first step was to turn it off.
After that it was a matter of removing the top burners,range knobs and locate the panel screws that secure it to the stove.Locate the part,remember the colors of where the wire s go,remove,replace wires,replace new part with wires,slide into place, and reassemble.
Turn on electriciy and Tada. Success.

Thank
18 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frederick from Eagle, WI
Parts Used:
32020101
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Spark did not ignite one burner and sometimes two
I could not figure out how to get to the igniter until I went to the "Part Select" web site and found a post that was exactly like the problem that I had. IE: Remove two screws holding each burner, Lift off top, remove old igniter being "Carefull" not to mix up the wires when putting them on the new one, installed new igniter in bracket a nd mounted in position, Reinstalled top and PRESTO - it worked. First post was VERY HELPFUL. Thank you
14 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!