Models > AKT3650E

AKT3650E (P1143731N E) Amana Cooktop

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for AKT3650E

Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
Sold individually.
In Stock
This surface element is made for under glass set-ups and supplies the heat to a cooking area on top of the range. It has an outside diameter of approximately 7 inches (1500 watts), and is a genuine OE...
In Stock
Use this scraper for your ceramic/glass cooktop. It has a retractable blade and is an all-purpose tool for cooktops, mirrors, windows and tile. Use it to also remove paint, paper, dirt, stickers and more.
In Stock
This is an OEM part sourced directly from Amana. This surface infinite element switch is commonly used in ranges and cooktops. This switch is designed to turn the surface element on and off, as well a...
In Stock
This is an authentic Amana replacement part. This dual radiant element is designed for use with cooktops and ranges. The dual radiant surface element is what supplies heat to the cooking surface of yo...
In Stock
In Stock
$9.12
This screw is sold individually. Size: 8-32 x 1/4 inch.
Special Order
This is a 2000 watt 240 volt surface element.
In Stock
Sold Individually. This knob accepts a D-shaped shaft.
No Longer Available
This is a 1200 watt / 240 volt surface element.
No Longer Available
$18.46
Special Order
This knob is used for a dual burner and takes a double-flat shaft.
No Longer Available

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for AKT3650E

Viewing 1 of 1
Element will not heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mark from Richardson, TX
Parts Used:
W10823726
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Outer Heater ring not working on dual burner.
Turned off power to unit.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws hol ding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.

Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
24 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephen from Seneca, SC
Parts Used:
12002422
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Burner switch failed (full on, even in "lo")
Managed to reach down from the top, unscrew the old part, so I could remove from under the cooktop. Easy to trace the wires, and map them to the (slightly different) replacement. Works like a charm, and new part appears to be of higher quality than the old one.
21 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffrey from Miami Lakes, FL
Parts Used:
W10823710
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
The burner was not heating up
I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together.
I am sure that I saved at least $200 in "lab or".
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!