AK2H300E (P1156301S) Amana Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Farouk from Sudbury, MA
- Parts Used:
- W11122012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Replacement of burner control switch
1. Open the circuit breaker feeding the range. Turn all range control switches ON to establish that there is no power. Remove all knobs.
2. Get under the range and remove the 2 hex-head screws securing the flex conduit to the bottom panel. Then remove the 20 hex-head screws securing the panel to the range. Lower the panel and place aside, and then after checking for no voltage disconnect the red and black incoming wires by pulling on the spade connectors. Make sure you mark which wire went where.
3. From below apply pressure to the range frame to free the top surface gasket from collected food debris, then from above lift our the range and place upside down on a towel. Support the range with wooden blocks so that the unit is not resting on the knob shafts.
4. The control switches are all mounted on a common bracket with two screws for each switch. The first task is to remove two screws on each side holding the bracket to the frame, and then two wire harnesses on each side. Then gently move the bracket and rotate it sidewards so you have access to the screws holding down the switches.
5. Remove the defective switch leaving all the wires still connected.
6. Install the new switch and transfer the wires from the defective switch.
7. You're done, now restore everything in reverse, just make sure all wires move freely and not pinched.
2. Get under the range and remove the 2 hex-head screws securing the flex conduit to the bottom panel. Then remove the 20 hex-head screws securing the panel to the range. Lower the panel and place aside, and then after checking for no voltage disconnect the red and black incoming wires by pulling on the spade connectors. Make sure you mark which wire went where.
3. From below apply pressure to the range frame to free the top surface gasket from collected food debris, then from above lift our the range and place upside down on a towel. Support the range with wooden blocks so that the unit is not resting on the knob shafts.
4. The control switches are all mounted on a common bracket with two screws for each switch. The first task is to remove two screws on each side holding the bracket to the frame, and then two wire harnesses on each side. Then gently move the bracket and rotate it sidewards so you have access to the screws holding down the switches.
5. Remove the defective switch leaving all the wires still connected.
6. Install the new switch and transfer the wires from the defective switch.
7. You're done, now restore everything in reverse, just make sure all wires move freely and not pinched.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Sunnyvale, CA
- Parts Used:
- W11122012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
2 controls were damaged and not working correctly. One would not properly shut off.
1. Turned off the 240V branch circuit to the cooktop.
2. Removed and inverted the cooktop.
3. Removed the bottom panel, used 1/4-inch nut driver to remove the sheet metal screws.
4. Confirmed the circuit was de-energized. Voltmeter set to AC, measure across the L1, L2 connections, should be 0 VAC or very close.
5. Make a diagram of the existing connections to the controls to be replaced, note all control markings (L1, L2, H1, H2, PL) as the replacement controls have connectors in different locations.
6. Remove the AC Mains plate, 2 sheet metal screws.
7. Make a diagram of the primary AC distribution blocks.
8. Remove the AC Mains input leads, Red and Black.
9. Remove the AC distribution to the controls from the primary AC distribution blocks. Needed to free up the control panel.
10. Remove the 4 sheet metal screws holding the control panel.
11. Rotate the control panel to access the screws holding the controls. Caution on the wires to the heating elements, watch for pinching.
12. Remove one control with the wires attached.
13. Install the replacement control. Secure the screws.
14. Transfer the wires, matching the connection marking (L1, L2, H1, H2, PL) exactly.
15. Do the same (12, 13, 14) with the next control.
16. Re-install the control panel. Check all wires for clearance.
17. Re-connect the control wiring to the AC primary distribution blocks.
18. Re-connect the AC mains wiring to the primary AC distribution blocks.
19. Re-install the AC mains plate.
20. Visually check all the connections. Shake out any debris.
21. Replace the bottom cover, installing all screws.
22. Remove the gasket strip from the mounting lip, clean the surface, install new gasket (weather stripping).
23. Re-mount the cook top.
24. Energize the 240VAC branch circuit.
25. Test the controls. Correct any errors.
26. Done! Go have some hot tea! (or a beer)
2. Removed and inverted the cooktop.
3. Removed the bottom panel, used 1/4-inch nut driver to remove the sheet metal screws.
4. Confirmed the circuit was de-energized. Voltmeter set to AC, measure across the L1, L2 connections, should be 0 VAC or very close.
5. Make a diagram of the existing connections to the controls to be replaced, note all control markings (L1, L2, H1, H2, PL) as the replacement controls have connectors in different locations.
6. Remove the AC Mains plate, 2 sheet metal screws.
7. Make a diagram of the primary AC distribution blocks.
8. Remove the AC Mains input leads, Red and Black.
9. Remove the AC distribution to the controls from the primary AC distribution blocks. Needed to free up the control panel.
10. Remove the 4 sheet metal screws holding the control panel.
11. Rotate the control panel to access the screws holding the controls. Caution on the wires to the heating elements, watch for pinching.
12. Remove one control with the wires attached.
13. Install the replacement control. Secure the screws.
14. Transfer the wires, matching the connection marking (L1, L2, H1, H2, PL) exactly.
15. Do the same (12, 13, 14) with the next control.
16. Re-install the control panel. Check all wires for clearance.
17. Re-connect the control wiring to the AC primary distribution blocks.
18. Re-connect the AC mains wiring to the primary AC distribution blocks.
19. Re-install the AC mains plate.
20. Visually check all the connections. Shake out any debris.
21. Replace the bottom cover, installing all screws.
22. Remove the gasket strip from the mounting lip, clean the surface, install new gasket (weather stripping).
23. Re-mount the cook top.
24. Energize the 240VAC branch circuit.
25. Test the controls. Correct any errors.
26. Done! Go have some hot tea! (or a beer)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from cleveland, TX
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner Would,Nt Heat Up.
Removed top of stove replaced heating element ,piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Fairport, NY
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the burner wasn't light up.
The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.
Was this instruction helpful to you?
Thank you for voting!