AKS3050WW (P1142526NWW) Amana Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- HUY from ALISO VIEJO, CA
- Parts Used:
- WPY0316773
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken Electrode, no spark
Remove 2 screws holding the top burner. Remove 1 screw holding the electrode. Remove electrode from wiring using plier. Install new electrode and top burner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Friendswood, TX
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not ignite when control in "light" position
Remove the two screws from the burner assembly (on top of the burner). Lift burner assembly from the cook top. Disconnect the electrode wire from the electrode. Remove the screw holding the electrode to the burner assembly (on bottom of burner). Install the new electrode and attach the electrode to the burner assembly. Attach the electrode wire to the electrode. drop the burner assembly back into position on the cooktop. Attach the burner assembly using two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Fishkill, NY
- Parts Used:
- Y0316705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Switch Spark would not stop sparking.
I was able to remove the top cover by unscrewing 10 srews. Once the cover was off I removed the plastic shield above the damaged switch. Then unplugged the 2 wires off the switch. Pulled the faulty switch out. Replaced it with the new switch and plugged in the 2 wires. Reinserted the plastic cover put the top cover on and put the screws in place. Tested the new switch and worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemarie from Huntington, NY
- Parts Used:
- Y0315769, WP7504P109-60
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Ignitor couldn't be removed because the screws were ruined.
This is the second time I have had to call a repair person to GE the old screws off. It isn't the fault of the part. Better original screws would have helped. It was very frustrating an expensive. I would say check the screws before you order the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Seattle, WA
- Parts Used:
- WP7504P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the burners would not autolight, had to be lit with match
This was VERY easy and I've never worked on this type of appliance before.
First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).
Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set them aside so they don't fall back into the stove, then pick the burner up off the stove.
once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.
Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.
First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).
Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set them aside so they don't fall back into the stove, then pick the burner up off the stove.
once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.
Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Glenwood Springs, CO
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ignition electrode broke
Removed the two screws that hold the element in place. Disconnected the wire to the electrode. The screw holding the electrode to the burner plate would not unscrew so I had to drill out the screw in order to replace it with the new ignition electrode. A little more time involved but if the screw would have come out it would have been a 10 minute job.When I ordered the part from you it came very quickly and I will certainly use you again when I have any other issues.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from hillsboro, OR
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none of the burners would light
I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sonora, CA
- Parts Used:
- WP7504P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not ignite even with gas flow spark and clicking.
Removed two screws and disconnected the ignition wire. Then connected ignition wire to new burner and installed two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from St. Louis, MO
- Parts Used:
- WPY0316773
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
The spark was no longer igniting the burner
The earlier reviews said very easy and 15 minutes for beginners. They were right on, except I could not get the old screw out no matter what I tried. I eventually had to drill it out and put in a self tapping new screw. This was a first for me. Then it took 15 minutes or less and works fine again. Hopefully next time someone will tell me how to get that old screw out faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Woodstock, IL
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replace Ignition Electrode gas range
Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Philadelphia, PA
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
cracked ignitors (2)
No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads did snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from CONCORD, CA
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear burner of sealed cartridge did not light
I removed the cartridge from the range and used a screw driver to remove the screws holding the burners assembly in the housing. (Some prefer to remove the burner from the top by removing the two screws, but I've had trouble realigning the parts that way.) I removed the ignition wire and the screw holding the bad electrode in the burner. I then installed the new electrode, attached the ignition wire, put the burners assembly back into the housing, and put the housing back into the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from ROLLING MDWS, IL
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no spark
I used your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Naperville, IL
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
range would not lite
diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service
Ordered one day arrived next with standard shipping installed before next day supper awesome service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily from Silver Spring, MD
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ignition no longer work
It was really easy because I read information on your site. I only had to unscrew 3 screws, remove the old spark ignition electrode, replace the new one and then screw the 3 screws back. It was great
Was this instruction helpful to you?
Thank you for voting!