Models
>
PGT136UD
PGT136UD (P1131480N D) Amana Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for PGT136UD
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
This clip is well under an inch in diameter. It is made of metal and it will help secure a range's electrode.
No Longer Available
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for PGT136UD
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Ranchos de Taos, NM
- Parts Used:
- Y705823
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burners kept clicking after ignited
After I bought this part, installed it and the clicking still did not stop I finally found the problem. If your ignitor can still click then it's still good. The problem is the electric connection between the head burners and the base burners (Top Assembly diagram). Put a little weight on the head burner while grabbing it with your hand a
... Read more
nd grind it into the base burner with a little twisting motion. Repeat for all 4 burners. Presto! (you could be more professional and use steel wool or sandpaper to.)
If you stll want to know how to install this part begin by removing the control panel bracket #24. Then remove the glass top w/seal #9 (after removing the knobs). You may have to tease this out because the rubber seal is sticky. The switch plate #14 comes off after removing 2 obvious screws at each end and 2 not-so-obvious star screws attaching it to the manifold #6. Remove the spark module by removing 2 of the 3 screws and sliding it out of the 3rd screw.
If you stll want to know how to install this part begin by removing the control panel bracket #24. Then remove the glass top w/seal #9 (after removing the knobs). You may have to tease this out because the rubber seal is sticky. The switch plate #14 comes off after removing 2 obvious screws at each end and 2 not-so-obvious star screws attaching it to the manifold #6. Remove the spark module by removing 2 of the 3 screws and sliding it out of the 3rd screw.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Martinsville, IN
- Parts Used:
- WP3185804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was a crack in the porcelain not letting it spark
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from San Bruno, CA
- Parts Used:
- WP3185804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
broken ignitor insulation; repeated sparking after burner lit
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Was this instruction helpful to you?
Thank you for voting!