Models
>
CL0501510
CL0501510 Powermate Compressor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CL0501510
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$39.07
This is an authentic OEM replacement part that has been sourced directly from Powermate. This is the knob used to regulate the amount of pressure leaving the air compressors tank. This knob allows you...
In Stock
$52.67
This is a genuine OEM replacement part that has been sourced directly from Powermate. The regulator on your air compressor controls the amount of pressure leaving the air compressor tank. The level of...
In Stock
$24.67
This is a genuine OEM replacement part that has been sourced directly from Powermate. This spring is part of the regulator assembly; it sits below the regulator knob. The regulator in your air compres...
In Stock
In Stock
$32.30
This is an authentic OEM replacement part that has been sourced directly from Powermate. The petcock on your air compressor is also known as a drain valve. While your compressor is pressurizing air a ...
On Order
In Stock
$14.13
This is a genuine OEM replacement part that has been sourced directly from Powermate. This 3/8 inch nut is commonly used in the assembly of your air compressor. These nuts can be found at either end o...
In Stock
In Stock
$23.48
This is a genuine OEM replacement part that has been sourced directly from Powermate. This tube is ? of an inch in diameter and it is 28 inches long. It is runs from a check valve to a discharge port....
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from AUBURN, WA
- Parts Used:
- 033-0001
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
hubcap fell off my coleman air compressor
repair didn't happen the part was the wrong size so i wasted $20 and my time because the part was on back order (which the website did not show) Will never use you service again, complete waste of time and money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Chandler, AZ
- Parts Used:
- 048-0074
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Compressor pump not filling ballast tank
1.) Disassemble the pump/motor assembly located on the top of the unit:
a.) Remove outermost plastic shroud. You will need a nut driver with an extension to get to one hex screw - a good Xcelite set will do.
b.) Remove inner plastic shroud with filter sponge. If filter sponge is clogged, replace it.
c.) With plastic s ... Read more hrouds removed, begin disassembling the metal pump components. Start by removing the four screws around the dome cover.
d.) Remove last two screws holding valve plate to piston housing case and remove.
e.) Remove the piston cylinder from the piston housing by lifting up.
f.) Loosen the clamp screw holding the piston rod to the bearing. Pull the piston away from the bearing - you might have to wiggle or pry on it a bit to slip it off. If you have to pry it off, pry only the piston rod itself - take care not to damage the bearing.
2.) Inspect gaskets for wear or damage - replace as necessary. For Piston and Cylinder assembly kit purchased from Parts Select, a gasket mated between the cylinder and valve plate will be included.
3.) Inspect valve plate for bent valve reeds or for debris caught between the valve reeds and the plate. Remove any material found and replace valve reeds as necessary.
4.) Reassemble by following instructions from step 1 in reverse. Mind the torque specifications - images are available online for these torque specifications.
a.) Remove outermost plastic shroud. You will need a nut driver with an extension to get to one hex screw - a good Xcelite set will do.
b.) Remove inner plastic shroud with filter sponge. If filter sponge is clogged, replace it.
c.) With plastic s ... Read more hrouds removed, begin disassembling the metal pump components. Start by removing the four screws around the dome cover.
d.) Remove last two screws holding valve plate to piston housing case and remove.
e.) Remove the piston cylinder from the piston housing by lifting up.
f.) Loosen the clamp screw holding the piston rod to the bearing. Pull the piston away from the bearing - you might have to wiggle or pry on it a bit to slip it off. If you have to pry it off, pry only the piston rod itself - take care not to damage the bearing.
2.) Inspect gaskets for wear or damage - replace as necessary. For Piston and Cylinder assembly kit purchased from Parts Select, a gasket mated between the cylinder and valve plate will be included.
3.) Inspect valve plate for bent valve reeds or for debris caught between the valve reeds and the plate. Remove any material found and replace valve reeds as necessary.
4.) Reassemble by following instructions from step 1 in reverse. Mind the torque specifications - images are available online for these torque specifications.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from LA PORTE, IN
- Parts Used:
- 034-0202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
pressure switch went out
Out with the old in with the new. came with instructions which made it a breeze..
Was this instruction helpful to you?
Thank you for voting!