Models
>
F412
F412 (Type 1) DeVilbiss Compressor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for F412
Viewing 1 of 1_WW_1.gif "Page A Diagram and Parts List for Type 1 DeVilbiss Compressor")
Keep searches simple, eg. "belt" or "pump".
$7.91
This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, a...
In Stock
Order now and your part arrives by Apr 6
$88.25
This kit is an OEM part direct from Craftsman for air compressors. This kit consists of the parts for building a piston cylinder in the compressor. It is recommended that you release air and unplug th...
In Stock
Order now and your part arrives by Apr 6
$14.47
This fan is an OEM direct from Craftsman for air compressors. This part cools the air compressor and connects to end of the motor shaft to prevent the air compressor from overheating. You will need a ...
In Stock
Order now and your part arrives by Apr 6
This rod kit is an original part from Craftsman for air compressors. This part attaches to the piston to the crankshaft that is in the pump. This kit includes the following: cylinder head, piston, cyl...
No Longer Available
$6.51
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many cause...
In Stock
Order now and your part arrives by Apr 6
$71.51
This replacement valve plate assembly is a high quality item designed for use on Craftsman air compressors. It is a genuine manufacturer sourced item that is used to control the airflow into the cylin...
In Stock
Order now and your part arrives by Apr 6
$8.17
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes f...
In Stock
Order now and your part arrives by Apr 6
This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentiall...
No Longer Available
This is a manufacturer approved replacement muffler used on air compressors. Muffler softens the noise coming from the engine and provides an additional filtering. This Kit includes the Plastic Filter...
No Longer Available
$6.51
This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to ...
In Stock
Order now and your part arrives by Apr 6
$49.72
This power cord is a genuine high quality item, it is not an aftermarket imitation. It is sourced directly from original equipment manufacturer for use with electric air compressors. It is connected t...
In Stock
Order now and your part arrives by Apr 6
$6.51
It is an OEM component which is designed for use with air compressors. This special nut sleeve assembly secures the pressure relief tube to the pressure switch. It is a high-quality replacement for a ...
In Stock
Order now and your part arrives by Apr 6
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for F412
Viewing 2 of 2
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from GARRISON, TX
- Parts Used:
- K-0650
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The air was bypassing the compressor gaskets and cylinder wall was worn out
1 remove cover
2 unhook air line to tank
3 remove head bolts
4 remove intake from head
5 remove flywheel bolt to free up pump piston
6 remove screw on top of piston to change out gasket
7 remove the cylinder sleeve install piston from the top
8 reassemble piston rod end and the flywheel
9 on th ... Read more e head cover are two gaskets one on top and one on the bottom head
10 insert intake piece and bolt the head cover back in place
11 reinstall the air line and unit cover and secure with three cover screws
2 unhook air line to tank
3 remove head bolts
4 remove intake from head
5 remove flywheel bolt to free up pump piston
6 remove screw on top of piston to change out gasket
7 remove the cylinder sleeve install piston from the top
8 reassemble piston rod end and the flywheel
9 on th ... Read more e head cover are two gaskets one on top and one on the bottom head
10 insert intake piece and bolt the head cover back in place
11 reinstall the air line and unit cover and secure with three cover screws
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Tucson, AZ
- Parts Used:
- ACG-408
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Can't find this special screw used on many housings etc
Actually don't like using Torx bits because they are hard to center deep in the channel. I had misplaced these forcing me to order replacements.
My plan is to insert Torx bits before screwing in and using jb weld to secure the bit to the screw, giving me a hex head. Can't find this special screw with a hex head. This screw is called ... Read more AGC-408 by craftsman.
My plan is to insert Torx bits before screwing in and using jb weld to secure the bit to the screw, giving me a hex head. Can't find this special screw with a hex head. This screw is called ... Read more AGC-408 by craftsman.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from PRESCOTT VLY, AZ
- Parts Used:
- D26615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ground on original plug
Removed cover & old cord.
Replaced with new cord & replaced cover.
Works perfect.
Replaced with new cord & replaced cover.
Works perfect.
Was this instruction helpful to you?
Thank you for voting!