Models > PP4218AVX

PP4218AVX Poulan Chainsaw

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for PP4218AVX

Viewing 2 of 2

Manuals & Guides for PP4218AVX

Click to download
Keep searches simple, eg. "belt" or "pump".
This fuel filter is for lawn and garden equipment engines. Fuel filter cleans the fuel before it reaches the carburetor. Work in a well-ventilated area when installing this part. Drain the fuel...
In Stock
Order within the next 6 hrs and your part ships today!
This chainsaw fuel line kit carries fuel from the tank into the carburetor and from the primer bulb to the fuel system. This part is mostly used on gas trimmers and blowers. The fuel lines are made fr...
In Stock
Order within the next 6 hrs and your part ships today!
This is a tank purge line, also known as a fuel line kit, and it is used with various lawn equipment. The line connects fuel from the tank into the carburetor, and from the primer bulb back into the f...
In Stock
Order within the next 6 hrs and your part ships today!
If your engine is having trouble starting, you may be in need a new purge bulb. When the engine has been sitting for a while, unused, the fuel will drain and eventually dissolve out of the carburetor....
In Stock
Order within the next 6 hrs and your part ships today!
This part is the replacement fuel cap assembly for your chainsaw. It is made of black plastic and is sold individually. The fuel cap prevents fuel from spilling out of the chainsaw and prevents debris...
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
$52.31
This is an authentic replacement carburetor which is supplied by the original equipment manufacturer for use with Craftsman chainsaws. The purpose of this part is to mix the air and the gas before the...
In Stock
Order within the next 6 hrs and your part ships today!
In Stock
Order within the next 6 hrs and your part ships today!
This is a washer kit for a chainsaw. This kit includes the retaining washer, C-ring, and the washer that is located between the clutch and clutch drum assembly. The outer washer acts like a shoulder t...
In Stock
Order within the next 6 hrs and your part ships today!
This is a genuinely sourced air filter for a chainsaw, sold as one unit. A dirty or worn air filter can decrease the life and performance of the engine and increase the amount of fuel consumed, which ...
In Stock
Order within the next 6 hrs and your part ships today!
This is a 3ft rope for a variety of power tools, most commonly chainsaws. It twists around the pulley of the recoil starter, which will allow you to pull-start the engine. This part is made of a durab...
In Stock
Order within the next 6 hrs and your part ships today!
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for PP4218AVX

Viewing 2 of 2
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Engine stops after a few seconds or minutes
Fixed by these parts
Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Victor from SCOTTSVILLE, KY
Parts Used:
530069247, 530069216, 530095646
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
Both the Fuel line and the Engine fuel line, where dry rotted.
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines.
2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fa ll into the path of the new fuel lines installation.
4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor.
5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line.
6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary.
7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
34 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Casper from ERATH, LA
Parts Used:
530069247, 530069216, 530095646
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Fuel and Purge lines had disintegrated
Disassembled it and cleaned fuel tank. Cut and ran new fuel lines, installed filter and reassembled. Parts fit perfectly and got running after not running for over 20 years.
19 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from MANVILLE, NJ
Parts Used:
580940901, 530069247, 530069216, 530057869, 530047721, 530023877, 530095646
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Replace the fuel lines
Replaced all fuel lines. Followed instructions found on Partselect.com, which said to insert cut fuel line in tank and use forceps to reach back in the tank and pull the fuel line through. The problem was that I did not have forceps, or needle nosed pliers that could reach the end of the hose.

Instead of running the line into the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through.
15 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!