Models
>
362
362 Husqvarna Chainsaw
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 362
Viewing 70 of 70
Keep searches simple, eg. "belt" or "pump".
$6.51
This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missi...
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
$9.32
By replacing your spark plug as part of your regular maintenance, this ensures a better performing engine, cleaner exhaust, faster starting, and a smooth-running engine. This spark plug is sourced dir...
In Stock
Order now and your part arrives by Apr 23
$6.51
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part...
In Stock
Order now and your part arrives by Apr 23
$6.51
This is a genuine Husqvarna replacement part sourced directly from original equipment manufacturer for use with lawn mowers/tractors. It is commonly used in riding mowers to keep the gauge wheel in pl...
In Stock
Order now and your part arrives by Apr 23
$12.91
This genuine Craftsman hex gauge wheel is a replacement part sourced directly from the original manufacturer and is designed for use with riding lawn mowers. It attaches to the mower’s deck assembly a...
In Stock
Order now and your part arrives by Apr 23
$6.51
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to ...
In Stock
Order now and your part arrives by Apr 23
$13.02
This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If ...
In Stock
Order now and your part arrives by Apr 23
$13.97
Located inside the fuel tank, the fuel filter removes debris before it can reach the carburetor. If your small engine starts with difficulty or idles rough, it may be clogged, restricting the flow of ...
In Stock
Order now and your part arrives by Apr 23
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most mod...
In Stock
Order now and your part arrives by Apr 23
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are ...
In Stock
Order now and your part arrives by Apr 23
$30.03
This is an OEM replacement part, sold individually. The High Lift Blade is also referred to as a 2 in 1 blade. It throws the clippings better, and is used when you are just discharging or bagging the...
In Stock
Order now and your part arrives by Apr 23
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from CANBY, MN
- Parts Used:
- 587820301
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Worn out Mandrel Assemblies
Remove Deck, Remove Blades, Remove guards and belt, use old belt to hold pully to remove pully (would be good to have pully wrench), Remove mandrel Assembly, Install new mandrel assemblies (had to tap the new mandrel assemblies. Should have been done by manufacturer.). Reinstall blades, guards, and belt. Put deck back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Hickory, NC
- Parts Used:
- 532177968
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Lound deck noise when mower put into motion
Parked mower on level concrete drive, laid on cardboard. Lowered mower deck all the way. Sparayed some WD40 on nut/bolt on top of old pulley. Since it is a carriage type bolt, placed 5/8" boxed end wrench over self locking nut on top of old pulley. Using some force from 3lb mallet to break nut free (hitting against wrench body), the nut c
... Read more
ame off easy as did broken pulley/bearing inside. Installed new pulley assembly, re-tightened nut on bolt. Checked after first mowing just to be certain pulley was in place and locking nut tight.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ALGOMA, WI
- Parts Used:
- 503718201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
part not same
Ordered on/off switch. My switch had only one wire terminal. Replacement had two. I ran a wire from one to a screw as a ground. Switch worked fine.
Was this instruction helpful to you?
Thank you for voting!