Models
>
CS-303T
CS-303T (C26213001001 - C26213999999) Echo Chainsaw
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CS-303T
Viewing 12 of 12Keep searches simple, eg. "belt" or "pump".
$21.97
This a manufacturer-packaged tune-up kit that is commonly used for Echo chainsaws. Routine engine maintenance extends the life of your outdoor power equipment. This kit contains a fuel filter, a spark...
On Order
$3.99
Replacing the spark plug should be part of your regular maintenance. How often to replace it depends on your model but is generally changed at least once a year or more, depending on use. When a spark...
In Stock
$7.63
This check valve or the fuel tank vent is connected to the fuel tank in the following products: hedge trimmer, leaf blower/vacuum, chainsaw, edger, engine, tiler, auger, water pump, chipper shredder, ...
In Stock
On Order
$7.72
This is a bevel gear, also referred to as a drive gear or tension gear, and is used in chainsaws. This authentically sourced part is sold individually. It is part of the chain tensioning assembly, aid...
In Stock
$4.99
This is an authentic OEM replacement flange nut, sold as an individual part. It is compatible with various types of equipment and is used to secure components, such as a guide bar cover, sprocket guar...
In Stock
$7.72
This is a single bevel gear for a chainsaw. Your chainsaw has two bevel gears that allow you to adjust the chain tension. One has a post with a slot in it (for a screwdriver), which mates to a second ...
On Order
$4.99
This part is the replacement stud for your chainsaw. It is approximately 1 ¼ inches long and is black in color. The stud secures the chain bar to the chainsaw. It the stud is damaged or missing, it ca...
In Stock
$10.87
This is a single air filter for a chainsaw. It is sourced right from the original manufacturer, ensuring the exact fit for your equipment. The air filter is essential in protecting the engine, as it f...
On Order
$4.99
This is a clip for a variety of lawn and garden equipment. The clip is made of a durable metal, and is 6.5mm in diameter. This part is most commonly used to clamp tubes and hoses in place. The clip is sold individually.
In Stock
$5.19
This is a cap for a chainsaw fuel tank. Its purpose is to seal the fuel tank and stop gas from leaking. The retainer stays inside the tank and ensures the cap stays connected and does not get lost. It...
In Stock
$4.99
This is an OEM quality chain tensioner for a chainsaw. This part is attached to the adjustment screw and fits into an opening on the bar. When you turn the adjuster it moves the tensioner, which eithe...
On Order
On Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from SPRING HILL, FL
- Parts Used:
- 12318139130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bulb was worn out and broken open
The unit is a press fit. To remove the old one required breaking the plastic compression tabs that hold it in place. That was simple enough. Replacing requires lining up in the correct position to meet the inner hose. Then push it in. The compression tabs on the replacement click in and hold.in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from GAITHERSBURG, MD
- Parts Used:
- V651000001, V355000140, V203000041, V651000011, C309000030, 90025304012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
worn out paddles and scrapper blade
I followed the instructions on Youtube, but I used an Impact drill and ratchet set. The hardest part is assembling the screw on the lower part of the paddle. It helps if you have your snow blower against a wall or something else so that it can not move b/c you will need some strength to push the screw threw the pre-drilled hole to the 10
... Read more
mm nut. I used a vise grip to hold the nut do to the lack of space and with my impact driver started to thread the screw to the nut. This part took about 1 min on one side and 10 minutes on the other side. I guess I got lucky the first time. Changing the scraper blade took about 4 minutes start to finish. It will help if you have needle nose pliers to remove and reattach the spring on each side. The instruction on you tube were very helpful. Hope you find this information helpful.
Read less
Was this instruction helpful to you?
Thank you for voting!