Models
>
1339-0
1339-0 Briggs and Stratton Generator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 1339-0
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$6.51
This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The metal washer is used to provide spacing between the steering sp...
In Stock
Order now and your part arrives by Apr 11
$6.51
This is a washer for various lawn and garden equipment. It is a flat washer and requires a 5/16-inch bolt size. Washers are positioned under the head of a nut or bolt to strengthen the connection of two or more parts.
On Order
$27.80
This fuel valve with bushing fits a variety of outdoor equipment and allows the fuel to smoothly flow into the gas engine. The bushing part is pressed into the hole provided in the fuel tank and the f...
In Stock
Order now and your part arrives by Apr 11
In Stock
Order now and your part arrives by Apr 11
$6.51
This authentic manufacturer-sourced component is specially designed for Murray, Snapper and Simplicity lawn mowers. It is an identical replacement for a missing or a damaged hex nut that was installed...
In Stock
Order now and your part arrives by Apr 11
$15.72
This part is an original part from Briggs & Stratton and Snapper for use in generators and welders. The circuit breaker goes inside the control box and helps to control electricity flow. A screwdriver...
In Stock
Order now and your part arrives by Apr 11
$9.94
It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton generators and pressure washers. The purpose of this component is to reduce the...
In Stock
Order now and your part arrives by Apr 11
$6.51
This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The m...
In Stock
Order now and your part arrives by Apr 11
$156.67
This is a genuine manufacturer-sourced replacement part which is designed for use with Snapper and Briggs and Stratton portable generators. Over time batteries will become weaker and eventually will n...
Special Order
Special Order
$27.49
This is available as an individual replacement. The outlet is part of the control panel assembly. When replacing this item a wrench may be needed. It is made of metal and plastic and will need to be r...
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 1339-0
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PICAYUNE, MS
- Parts Used:
- 192980GS
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from RADFORD, VA
- Parts Used:
- 192980GS
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LEES SUMMIT, MO
- Parts Used:
- 192980GS
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Was this instruction helpful to you?
Thank you for voting!