Models
>
HGI8046UC/03
HGI8046UC/03 Bosch Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$24.74
This burner igniter creates the spark needed to light the surface burner. Made from ceramic and stainless steel, it’s built to withstand heat and wear. Replace it if your burner won’t ignite. Always u...
In Stock
Order now and your part arrives by Apr 16
$68.99
This wire oven rack provides a stable, flat surface for baking, roasting, and cooking, ensuring even heat distribution throughout the process. Designed for durability and a precise fit, it helps organ...
In Stock
Order now and your part arrives by Apr 16
$136.36
This push-to-open slide kit restores smooth, handle-free operation to warming drawers. It’s designed for select Bosch, Thermador, and Gaggenau ranges and allows the drawer to open and close with a gen...
In Stock
Order now and your part arrives by Apr 16
$55.18
This rubber feet kit includes four non-slip feet designed to provide stability and vibration reduction. They help protect surfaces while keeping the appliance securely positioned during use.
In Stock
Order now and your part arrives by Apr 16
$50.89
This genuine temperature sensor ensures precise heat regulation inside your oven for consistent cooking results and improved safety. Designed to measure the oven cavity temperature, it communicates wi...
In Stock
Order now and your part arrives by Apr 16
$112.86
This hot surface igniter helps light the gas burners in select ovens and ranges, ensuring quick and efficient ignition. It supports safe and consistent heating, and replacing a worn igniter can restor...
In Stock
Order now and your part arrives by Apr 16
In Stock
Order now and your part arrives by Apr 16
In Stock
Order now and your part arrives by Apr 16
$35.50
This burner cap is for cooktops. Burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
In Stock
Order now and your part arrives by Apr 16
$39.06
This burner cap is for cooktops. Burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
In Stock
Order now and your part arrives by Apr 16
In Stock
Order now and your part arrives by Apr 16
$39.06
Sold individually.
This burner cap is for cooktops. Burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
In Stock
Order now and your part arrives by Apr 16
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for HGI8046UC/03
Viewing 4 of 4Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Oven is too hot
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Bloomington, MN
- Parts Used:
- 00755058
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Igniter replacement
Getting to the igniter is trivial, only requiring the removal of the stove bottom (two set screws) and a heat shield (the heat shield is held in place by screws with size 20 star-driver heads). At this point a splice could be made to the original wires, IF ceramic wire nuts were included with the replacement igniter (but, alas, they are n
... Read more
ot). IF a splice were made the repair would be a very easy, 10-minute job.
To replace the igniter then requires the complete removal of the back of the range (17, size 20 star-driver, screws, if I remember correctly), plus the removal of an additional heat shield (one more screw). Then one must carefully lift and free the back from tabs on both sides that are set into slots. (Oh, and you probably want to loosen the electrical cord shield that interferes with the back coming off.) The new igniter wire plug is only then very easily re-attached to existing harness. Everything is then replaced to finish the repair.
None of this is difficult, if you don't mind moving your range away from the wall and dealing with on the order of 20 screws. Personally, I think I would have rather found an igniter with ceramic wire nuts to splice to the original wires (certainly not as elegant as replacing igniter and wires entirely, but far quicker and easier).
To replace the igniter then requires the complete removal of the back of the range (17, size 20 star-driver, screws, if I remember correctly), plus the removal of an additional heat shield (one more screw). Then one must carefully lift and free the back from tabs on both sides that are set into slots. (Oh, and you probably want to loosen the electrical cord shield that interferes with the back coming off.) The new igniter wire plug is only then very easily re-attached to existing harness. Everything is then replaced to finish the repair.
None of this is difficult, if you don't mind moving your range away from the wall and dealing with on the order of 20 screws. Personally, I think I would have rather found an igniter with ceramic wire nuts to splice to the original wires (certainly not as elegant as replacing igniter and wires entirely, but far quicker and easier).
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jaymie from Intercourse, PA
- Parts Used:
- 00642855
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven heating temp not turning off at set temp/overheating
Removed the wall oven to access temp probe connector strapped to the back of the oven. removed 2 screws holding probe inside the oven & replaced. Searched for the "fixing kit" thermostat part I was suggested to replace along with the probe. No thermostat type part was found in my oven, even though Bosch says it fits "somewhere". Reinstall
... Read more
ed the wall oven & tested. The temperature is working normal now. Will return the fixing kit.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from MONROE, NY
- Parts Used:
- 00630873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven was not heating properly
Took the one out of the box and take off the back plate and detach the sensor
Was this instruction helpful to you?
Thank you for voting!