Models
>
2106
2106 Makita Band Saw
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 2106
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will nee...
In Stock
Order now and your part arrives by Apr 23
$35.26
This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing y...
In Stock
Order now and your part arrives by Apr 23
$6.51
This is a cord guard, also known as a strain reliever, for your power tools. Power tool cords go through a lot of stress during usage, and this part is designed to remove some of that stress from the ...
In Stock
Order now and your part arrives by Apr 23
$24.26
Genuine Manufacturer Approved replacement Wheel Tire for some Makita Bandsaws. This part is made out of Rubber and is Sold Individually. When putting the tire on a band saw Wheel, it may seem too smal...
In Stock
Order now and your part arrives by Apr 23
$26.20
Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating par...
In Stock
Order now and your part arrives by Apr 23
$6.51
Manufacturer sourced replacement part designed for use on Makita power tools. The purpose of the brush cap is to hold the brush in the tool. This cap has external threads that thread into the housing ...
In Stock
Order now and your part arrives by Apr 23
$6.51
This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it ha...
In Stock
Order now and your part arrives by Apr 23
$31.31
This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise...
In Stock
Order now and your part arrives by Apr 23
$46.86
This is a Trigger switch that has 4 leads and a locking mechanism for the trigger. This authentic Makita replacement part is sold individually.
Switches are commonly replaced parts in power tool...
In Stock
Order now and your part arrives by Apr 23
$6.51
This is a genuine manufacturer approved replacement part. It is specially designed for Makita power tools. This screw is a standard hardware which has multiple used depending on a tool. Please refer t...
In Stock
Order now and your part arrives by Apr 23
$6.51
Genuine Makita replacement part.
This pan-head phillips screw includes a washer. It is sold individually.
In Stock
Order now and your part arrives by Apr 23
$6.51
This is an authentic manufacturer sourced replacement part. It is commonly used on a variety of Makita power tools. It is used to distribute the pressure evenly between two connected parts. Since this...
In Stock
Order now and your part arrives by Apr 23
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from HILLSBORO, OR
- Parts Used:
- 664064-4
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Old power cord frayed at the grommet entering the drill casing
Did not do repair as replacement part did not match description on partselect website. The grommet is not part of the replacement that was sent. Order #22962198
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Was this instruction helpful to you?
Thank you for voting!