Models
>
KCMS1555RSS
KCMS1555RSS
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Models for KCMS1555RSS
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Mar 21
In Stock
Order now and your part arrives by Mar 21
Special Order
In Stock
Order now and your part arrives by Mar 21
$20.95
This is an authentic OEM replacement part. This screw is commonly used in the assembly of refrigerators, microwaves, ice makers, ranges, and smokers. Due to varied uses we recommend you refer to model...
In Stock
Order now and your part arrives by Mar 21
$87.63
This kit contains 2 switches - 15 Amp - 125/250 Volt with 3/16" terminals.
In Stock
Order now and your part arrives by Mar 21
In Stock
Order now and your part arrives by Mar 21
In Stock
Order now and your part arrives by Mar 21
In Stock
Order now and your part arrives by Mar 21
Special Order
In Stock
Order now and your part arrives by Mar 21
Common Problems and Symptoms for KCMS1555RSS
Viewing 7 of 7Door stuck closed
Fixed by these parts
How to fix it
No heat
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Tray won’t turn
Fixed by these parts
How to fix it
Doesn’t shut off
Fixed by these parts
How to fix it
Door not closing properly
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sailendra from Round Rock, TX
- Parts Used:
- WP8205451
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
microwave door stuck....wont open
The reason the door would not open upon pressing the door opener is because the BRCKT-LATCH was broken. I discovered that after opening the microwave enclosing. The BRCKT-LATCH has two ends sticking out....each fits into a hole. One of the ends on the LATCH was broken and therefore it was not tightly fit. No upon pushing the door opener t
... Read more
he LATCH would not function properly since it was loosely fit and hence the door would not open.
To Fix this issue:
1) Buy a new BRCKT-LATCH
2) Remove the microwave enclosing. I had to use a special screwdriver, since the screws were security protected on my microwave. After removing the case, I opened the door by manually pressing the door latch upwards (please make sure that the microwave is not connected to the electric socket before removing the enclosing).
3) pull out the old LATCH from the microwave.
4) carefully insert the new LATCH. Try not to put too much pressure when trying to fit the latch, or else the ends may snap again!!
5) Close the door and try opening it by pressing the door opener. it should work now!!
To Fix this issue:
1) Buy a new BRCKT-LATCH
2) Remove the microwave enclosing. I had to use a special screwdriver, since the screws were security protected on my microwave. After removing the case, I opened the door by manually pressing the door latch upwards (please make sure that the microwave is not connected to the electric socket before removing the enclosing).
3) pull out the old LATCH from the microwave.
4) carefully insert the new LATCH. Try not to put too much pressure when trying to fit the latch, or else the ends may snap again!!
5) Close the door and try opening it by pressing the door opener. it should work now!!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bainbridge Island, WA
- Parts Used:
- 4392027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave worked intermittently depending on how door was closed
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and a
... Read more
lso took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from WHITE LAKE, MI
- Parts Used:
- 6600W1K001D, 6600W1K001C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would not rotate or heat up food.
After watching a few youtube videos, I used a phillips SD to take controll pannel off to access the switches that sense when microwave door is closed. Swapped out all 3 switched and mocrowave works like new. $20 fix (shipping included)
Was this instruction helpful to you?
Thank you for voting!