2800 - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Malcolm from Mt Pleasant, SC
- Parts Used:
- EBG61107109
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
LG Mini Split Air Conditioner Error Code CH 46
Remove the main power disconnect. Remove the top cover and the fan-side side panel. Disconnect the thermister from the main circuit board located under top panel. Remove the two thermister sensors from the holders attached to suction piping. Install the new thermisters and reconnect the harness to the circuit board. Reinstall top cover and side panel. Reinstall main power disconnect. Verify that error code has cleared. Operate the system normally.
Was this instruction helpful to you?
Thank you for voting!
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Yantis, TX
- Parts Used:
- EBG61107109
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Error CH 46 Suction Pipe Thermistor
Download PDF Multi Air Conditioner SVC Manual for LMU187HV,,, Disconnect the Power,,, Remove cover of the Outdoor Compressor, Remove black cover to the electronics board.. Find the Red Plug-in to the existing Suction Pipe Thermistor, replace with the new one, match each sensor (2) follow the leads one by one, remove the old attach the new ones... Replace covers then the Disconnect & Waa-Laa,,, Fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Taylor, MI
- Parts Used:
- 532419274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
bent mower blade
it was a 5 minute job all I did was jack up the rear of the mower lay down along side of it and install the new blade tighten up the bolt then I lower the mower back down to the ground the started up the mower for a test run of the blade. and it works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PILESGROVE, NJ
- Parts Used:
- 532123583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Take the wheel off. Place the key in the slot. Put the wheel back on.
Just described it.
Was this instruction helpful to you?
Thank you for voting!
Dryer runs no heat
Disassemble dryer. Replaced element assembly. Re assembled dryer. Unit runs and heats.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from BINGHAMTON, NY
- Parts Used:
- 532121749
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from CHEHALIS, WA
- Parts Used:
- EBG61107109
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
ERROR 46 Thermistor error
I removed the front panel. Then opened case with circuit board and thermistor connections. Cut zip ties securing wires and thermistor. Removed old thermistor and replaced with new part. Placed new zip ties to secure wires. Reassembled.
Was this instruction helpful to you?
Thank you for voting!