Maytag/Maytag_Thumb/OBEL0PDR.gif
See part 2 in the diagram
Replacing your Whirlpool Washer Agitator Cap Barrier with Seal play video
( Grid squares measure 1x1 inch )

Agitator Cap Barrier with Seal

$ 10.76   In Stock
Fix Number: FIX11748113
Manufacturer #: WPW10074580
Manufactured by: Whirlpool

Product Description

The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.

Videos For installing this part.

Replacing your Agitator Cap Barrier with Seal

Replacing your Agitator Cap Barrier with Seal play video

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 4.2 / 5.0, 6 reviews.
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Agitator not working correctly and leaking from somewhere underneath.
    I watched the videos before I ordered the part and when the order arrived I replaced the parts with no problems. The most time consuming part of the job was cleaning the washer. You will be surprised to find what will accumulate down there after years of service. The order came in in record time so this site gets an A+ for being fast and accurate. No back-orders either. I will surely use for any-other parts I need in the future.
    19 of 19 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    • Customer:
      Richard from Belle Chasse, LA
    • Parts Used:
      WPW10074580, WP3951608, 285809
    • Difficulty Level:
      Very Easy
    • Total Repair Time:
      15 - 30 mins
    • Tools:
    Top agitator not working
    Pull top cap, bolt,remove agitator , pull top half off remove old parts install new parts! About 15 minutes total
    2 of 2 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    leaks water as soon as tub starts to fill
    Tipped the machine on its side , undo the two hose clamps and two pump clips, then pull pump off motor drive. assemble reverse. very easy .. surprised at simplicity of such an expensive machime
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    • Customer:
      Drew from Nibley, UT
    • Parts Used:
      WPW10074580, WP3946501
    • Difficulty Level:
      Very Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Socket set
    The clothes mover on the agitator was not turning properly.
    This washer is 17 years old. The whole assembly didn't cost that much more than the parts I needed so I decided to replace the whole agitator assembly not just the dog ear assembly. The video on part select were helpful. I removed the fabric softener dispenser. Reached in and removed the cap barrier with seal. Did this by hand, needle nose pliers were not necessary. Remove the retaining bolt using a 7/16 socket wrench with a 8" extension. Reach in and grab the bottom of the lower agitator and pull the whole assembly straight up out of the washer. I assembled the new parts placing the thrust spacer on top of the agitator. I placed the preassembled cam with dog ears and bearing down into the bottom of the clothes mover. I placed the clothes mover onto the agitator making sure the cam assembly lined up with the thrust spacer properly before I snapped the clothes mover in place. This was the most difficult part of the assembly but was still easy I placed this assembly over the drive shaft of the washer and re-attached the retaining screw and washer. I coated the seal of the barrier cap with liquid detergent and placed it into the clothes mover. Snapped the fabric softener dispenser. Done, works great. It took longer for me to write this than it did to fix the washer.
    0 of 1 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    • Customer:
      JANET from BUFFALO, MN
    • Parts Used:
      WPW10074580
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
    Seal Was Broken
    Pulled the top off and placed the cap in place with seal in place.
    0 of 1 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    would not agitate clothes to good, they were not coming clean
    I followed the repair video you have on this. It was very easy to do. thank you.
    0 of 1 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Model Compatibility
      This part works with the following models:
      Fix Number: FIX11748113
      Manufacturer Part Number: WPW10074580
      Brand
      Model Number
      Description
      Kenmore
      11016922500
      Washer
      Kenmore
      11016922501
      Washer
      Kenmore
      11016922502
      Washer
      Kenmore
      11016922503
      Washer
      Kenmore
      11016922504
      Washer
      Kenmore
      11016942500
      Washer
      Kenmore
      11016942501
      Washer
      Kenmore
      11016942502
      Washer
      Kenmore
      11016942503
      Washer
      Kenmore
      11016962500
      Washer
      Kenmore
      11016962501
      Washer
      Kenmore
      11016962502
      Washer
      Kenmore
      11016962503
      Washer
      Kenmore
      11016964500
      Washer
      Kenmore
      11016964501
      Washer
      Kenmore
      11016964502
      Washer
      Kenmore
      11016964503
      Washer
      Kenmore
      11016972500
      Washer
      Kenmore
      11016982500
      Washer
      Kenmore
      11016984500
      Washer
      Kenmore
      11016986500
      Washer
      Kenmore
      11020052990
      Washer
      Kenmore
      11020052991
      Washer
      Kenmore
      11020056991
      Washer
      Kenmore
      11020072990
      Washer
      Kenmore
      11020092990
      Washer
      Kenmore
      11020096990
      Washer
      Kenmore
      11020097990
      Washer
      Kenmore
      11020112310
      Washer - AUTOMATIC WASHER
      Kenmore
      11020112311
      Washer - WASHER