Part Location Diagram of 12002213 Whirlpool Transmission Pulley and Bearing Kit
See part 35 in the diagram
Replacing your Maytag Washer Transmission Pulley and Bearing Kit
( Grid squares measure 1x1 inch )

Transmission Pulley and Bearing Kit 12002213

Works With Model W224LGV!

Rated by 19 customers 

?

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

?
$69.76
In Stock
Fix Number:
FIX2003651
Manufacturer #:
12002213
Manufactured by:
Whirlpool
Works With Model W224LGV!

Product Description

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY available in this kit. A worn bearing causes slow or no spin.

Videos For installing this part.

Replacing your Transmission Pulley and Bearing Kit

Replacing your Transmission Pulley and Bearing Kit

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

View More View Less
Drive Belt - 51 inches long
$10.97
In Stock
Snubber Ring
$13.09
In Stock
Drive Belt - 52 inches long
$37.73
In Stock
Affresh Washing Machine Cleaner - 3 pack
$12.58
In Stock
Produce Preserver Filter
$21.50
In Stock
Affresh Dishwasher Cleaner Tablets - 6
$19.09
In Stock
Cooktop Cleaning Cream
$15.57
In Stock
Cooktop Cleaner
$17.74
In Stock
Affresh Cleaner
$19.09
In Stock

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.1 / 5.0, 19 reviews.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Customer:
Ralph from Oakland, CA
Parts Used:
WP35-6780, 12002213
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Pump had stop displacing water at spin cycle
Facing washer placed it on right side exposing underneath. Pump and transmission bearing items are accessible from this position. Followed step by step instructions contained with each part. Placed unit upright,supplied power and ran smallest allowed cycle to test. Unit works like new. Actually spin drys better,dryer clothes which works o ur older dryer less. Great tune-up and should give us several more years of service.
8 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brandon from Keller, TX
Parts Used:
35-6714, WP22004376, 12002213, WP21002026
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer would run and agitate but would not spin.
Prior to the spin cycle not working, the washer would make a loud screeching noise when the spin cycle would stop. I wasn't sure if there was a problem with the break rotor or some bearing was out. Due to the washer's age, I decided to go ahead and replace the pulley, brake rotor, motor pivot spring and snubber ring components.
I be gan by unplugging the unit first, securing the lid with duct tape and laying the washer on its front face. I removed the belt and transmission pulley per instructions contained in the replacement kit. Mainly consists of popping the "E" ring off with a screwdriver. Once the pulley was off, I stood the washer upright and to access and remove tub. Having the tub out made it easier to compress the brake spring when re-attaching the brake stator. Removing the tub is easy, I just popped off the tub cover and tilted the tub around to ease the tension and remove the bottom springs with pliers (this may require an assistant). With the tub removed, I turned it over to remove the brake stator. USE CAUTION WHEN REMOVING THE BRAKE STATOR. A 200 LB BRAKE SPRING IS UNDER IT AND IS UNDER TENSION. With the new brake rotor and brake stator secured, I replaced the snubber ring and motor pivot spring. I put it all back together in reverse order and it spun like a top, is quieter and stops on a dime!
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lou from Saugerties, NY
Parts Used:
12002213
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
WASHER WOULD NOT SPIN DRY
Reviewed others experiences, reviewed the video, read the written instructions. Would have only taken less than 1/2 hour, but I had a problem getting the thin washer and "e" clip on. I ended up just putting on clip without washer but intend to go back at it in 2 weeks or so. Parts solved the problem and the quick shipping was outstanding !
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Sac City, IA
Parts Used:
12002213
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
It would agitate slowly and pump. It would only spin about 50% of the time. On and Off.
I followed the instructions to a tee!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Diana from ShowLow, AZ
Parts Used:
WP21352320, 12002213
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
noisy maching coming from the lower elements
I pulled the machine away from the wall, just enough to lean it back far enough to see the parts at the bottom of the unit. I rolled the belt from the big pulley, popped the dust cover from that pulley, removed the retainer clip, and the parts practically fell to a paper towel. replace them in reverse without any problem. Although I unpl ugged the machine, I did not remove the water hoses or drain line as sufficient room was available with the machine leaned against the wall.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Statesville, NC
Parts Used:
12002213
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Tub would not spin
Removed belt, clip, pulley and washers. Installed new pulley, greased, installed washer, clip and checked alignment. Reinstalled belt and test machine. Everything worked. Easy repair. Thanks for the video on how to.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from Denver, CO
Parts Used:
12002213
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench (Adjustable)
Bad thrust bearing
My tub wouldn't spin fast enough to get the water out of my clothes. The repair guy wanted $500 to replace my thrust bearing and snubber ring. I got the parts and fixed it myself in about an hour. The snubber ring didn't actually need to be replaced. The thrust bearing is an easy job. The only tricky part is the e clip. I was able to take it off and put it back on pretty easily with vice grips and a screwdriver used to fully extend the spindle. Washer works perfectly now.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jimmy from Flat Rock, MI
Parts Used:
12002213
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
drum not spinning but pumping out water
Washer Thrust Bearing Kit (part #12002213) This is a complete repair kit. that takes about 30 minutes.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Andew from Antelope, CA
Parts Used:
12002213
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Tub would weakly spin in rinse/spin cycle
Followed the two recommendation; purchased and installed belt and Transmission Pulley and Bearing Kit. Still had the problem after changing out. I believe it may be a brake or transmission problem.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nicholas from Queens Village, NY
Parts Used:
WP22003483, 12002213
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Machine would not spin during rinse cycle.
Had to replace the thrust bearing. Tilted machine on its back and removed the C clip that holds the bearing and drive pulley all together. Had to make sure the shaft was completely extended in the down position otherwise all the parts wouldn't all fit back on. Trickiest part was to figure out how the belt goes back on. Turns out it is ver y simple... just walk it back on to the drive pulley with a screwdriver as your turning the pulley.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2

Model Compatibility

This part works with the following models:
Fix Number: FIX2003651
Manufacturer Part Number: 12002213
Brand
Model Number
Description
Norge
6002A
Washer - WASHER
Norge
6430
Washer - WASHER
Norge
6432A
Washer - WASHER
Norge
6432A REV A
Washer - Norge Washing Machine Model 6432A REV A (6432AREVA) Parts
Norge
6432A REV B
Washer - Norge Washing Machine Model 6432A REV B (6432AREVB) Parts
Norge
6432A REV C
Washer - Norge Washing Machine Model 6432A REV C (6432AREVC) Parts
Norge
6432A REV D
Washer - Norge Washing Machine Model 6432A REV D (6432AREVD) Parts
Norge
6433A
Washer - WASHER
Norge
6440A
Washer - WASHER
Norge
6440A REV A
Washer - Norge Washing Machine Model 6440A REV A (6440AREVA) Parts
Norge
6440A REV B
Washer - Norge Washing Machine Model 6440A REV B (6440AREVB) Parts
Norge
6440A REV C
Washer - Norge Washing Machine Model 6440A REV C (6440AREVC) Parts
Norge
6440A REV D
Washer - Norge Washing Machine Model 6440A REV D (6440AREVD) Parts
Norge
6440A REV E
Washer - Norge Washing Machine Model 6440A REV E (6440AREVE) Parts
Norge
6440A REV F
Washer - Norge Washing Machine Model 6440A REV F (6440AREVF) Parts
Norge
6440A REV G
Washer - Norge Washing Machine Model 6440A REV G (6440AREVG) Parts
Norge
6440A REV H
Washer - Norge Washing Machine Model 6440A REV H (6440AREVH) Parts
Norge
6440A REV J
Washer - Norge Washing Machine Model 6440A REV J (6440AREVJ) Parts
Norge
6440A REV K
Washer - Norge Washing Machine Model 6440A REV K (6440AREVK) Parts
Norge
6443A
Washer - WASHER
Norge
6443A REV D
Washer - Norge Washing Machine Model 6443A REV D (6443AREVD) Parts
Norge
6443B
Washer - WASHER
Norge
6530A
Washer - WASHER
Norge
6530A REV A
Washer - Norge Washing Machine Model 6530A REV A (6530AREVA) Parts
Norge
6530A REV B
Washer - Norge Washing Machine Model 6530A REV B (6530AREVB) Parts
Norge
6530A REV C
Washer - Norge Washing Machine Model 6530A REV C (6530AREVC) Parts
Norge
6530A REV D
Washer - Norge Washing Machine Model 6530A REV D (6530AREVD) Parts
Norge
6530A REV E
Washer - Norge Washing Machine Model 6530A REV E (6530AREVE) Parts
Norge
6530A REV F
Washer - Norge Washing Machine Model 6530A REV F (6530AREVF) Parts
Norge
6530A REV G
Washer - Norge Washing Machine Model 6530A REV G (6530AREVG) Parts