This snubber ring fits washers and is located between the leg and dome assembly. The ring has a diameter of 9 inches. It is used to reduce noise and vibration for stability when the washer is operating. If your washer shakes a lot and makes loud noises, then it is best to replace this part to solve your problem. The tools required for this repair are: short flathead screwdriver, flathead screwdriver, Philips screwdriver, 1/4 inch nut driver, 5/16 inch nut driver, 3/8 nut driver, ratchet with extension, putty knife, locking pliers, slip joint pliers, and 3/8 inch socket.
Works with the following brands:
Maytag, Norge, Admiral, Magic Chef
Works with the following products:
Washer
Fixes the following symptoms:
Shaking and Moving, Spins slowly, Will not agitate
Part# WP21002026 replaces these:
AP6005786, 21001161, 21002026, 35-2357, 35-3699, 35-3788
...
Show more, WP21002026VP Show less
Works with the following brands:
Maytag, Norge, Admiral, Magic Chef
Works with the following products
Washer
Fixes the following symptoms
Shaking and Moving, Spins slowly, Will not agitate
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Barry
October 3, 2021
Maytag washer stopped spinning but pumps the water out. How do I resolve this problem
For model number MAV6548AWW
Hello Barry, Thank you for the question. The most common issues is a worn or broken Belt. We suggest checking the Belt first to verify it is intact. If the Belt is good, you can check the Transmission Pulley and Bearing Kit for wear or damage. We hope this helps!
Washer doesn’t spin at high speed. Spins but not fast enough to get water out clothing. Changed belt and pulley kit on bottom of transmission
For model number MAV408DAWW
Hello Chuck, thank you for contacting us. If replacing the belt and pulley kit does not solve the issue, we would recommend checking the motor, part number FIX11738839. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
This is a V-style drive belt that measures approximately 51-inches long and 3/8-inches wide. This part connects the drive motor to the drive system in the washer to turn the basket. It is prone to wear with time and requ...
This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot during operation, it coul...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Affresh® Dishwasher Cleaner is the #1 recommended cleaner by Whirlpool, KitchenAid, and Maytag brands, designed to remove limescale and mineral build-up that can affect your dishwasher’s performance. These powerful table...
Prior to the spin cycle not working, the washer would make a loud screeching noise when the spin cycle would stop. I wasn't sure if there was a problem with the break rotor or some bearing was out. Due to the washer's age, I decided to go ahead and replace the pulley, brake rotor, motor pivot spring and snubber ring components. I be
... Read moregan by unplugging the unit first, securing the lid with duct tape and laying the washer on its front face. I removed the belt and transmission pulley per instructions contained in the replacement kit. Mainly consists of popping the "E" ring off with a screwdriver. Once the pulley was off, I stood the washer upright and to access and remove tub. Having the tub out made it easier to compress the brake spring when re-attaching the brake stator. Removing the tub is easy, I just popped off the tub cover and tilted the tub around to ease the tension and remove the bottom springs with pliers (this may require an assistant). With the tub removed, I turned it over to remove the brake stator. USE CAUTION WHEN REMOVING THE BRAKE STATOR. A 200 LB BRAKE SPRING IS UNDER IT AND IS UNDER TENSION. With the new brake rotor and brake stator secured, I replaced the snubber ring and motor pivot spring. I put it all back together in reverse order and it spun like a top, is quieter and stops on a dime!
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The washer was jumping all over during spin cycles
The most difficult thing to do was to install the springs. I removed the sides and back, which made it much easier. Otherwise, I followed the instructions which were provided by others on the site.
Taking it apart was easy. I found that the new parts did not allow the slip ring that came with the new kit to fit the shaft even with the thinner washer. The new slip ring seemed to be thicker than the old one. I ended up using the old large pulley, the old cam and the old slip ring and thin washer to get it to fit. It did solve the nois
... Read moree problem.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Spring tension on drum.
This spring have so much tension they cannot be removed with one hand like the indicate in the video. Tube must be wedged towards the spring trying to be removed. Vise grips must be attached to the lower part of the spring not the upper and pry bar is needed to pry spring loose from base of unit. Be careful nothing slips where prying,
... Read morethere is a lot of tension on the springs.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Tub out of balance
Took springs off turn tube upside down undone screws and replaced snubber ring. Suspension springs put 3 on then used rolled up towel to hold tub tilted to side.Followed some. videoson how to fix it
The on-line video from this site was extremely helpful! It showed me almost exactly what to do. The only difference was that my washer did not have an access panel in the back of it like the one in the video. I had to remove the skin "shell" of the washer to get around to the back of the tub unit. It wasn't too hard and the entire rep
... Read moreair was done in about 2 hours. This was the first time I've ever attempted a repair like this so I'm sure that added to my repair time.
washer was shaking and walking , lid switch didn't engage
I did everything by the instuctions on your site, i used the vicegrips to attach the springs , i tipped the tub as much in the direction of the springs being installed and latched on the spring with vicegrips And attached it, no problem.The ring was no problem at all per instructions, the lid switch was ok installed the way it came off. T
... Read morehanks, Rod
washer would not stay in balance and at times cold water would not completely shut off
case top and front had to be removed, belt to pully removed, tub springs removed, install new snubber ring, remove and replace water valve. Hardest part of repair was putting springs back onto tub used vise grips to assist.
Machine was noisy during wash cycle and had teh infamous finger on wet glass screach.
After watching the online video and info I decided to tackle the repair from the bottom of the machine, tilted against the wall. I removed the lower pulley and belt then rotated out the # 10 screws with the 2 inch ones to relieve the brake rotor spring tension. The brake stator came off easily, with the spring and brake rotor to follow. S
... Read moreince the tub rests on the Snubber Ring, it is not possible to change it out from the bottom. From my visual inspection the snubber ring appeared intact, so left the old one in place. I installed the new Brake Rotor and Stator and put the lower pulley and belt back on. Tested the machine and it ran smooth as new.
Read less
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX11738845
Manufacturer Part Number: WP21002026
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
