Maytag/Maytag_Thumb/53161.gif
See part 8 in the diagram
Replacing your Maytag Refrigerator Ice Dispenser Solenoid and Door Kit play video
( Grid squares measure 1x1 inch )

Ice Dispenser Solenoid and Door Kit

$143.09
Fix Number: FIX2003478
Manufacturer #: 12001991
Manufactured by: Whirlpool

Product Description

In addition to the solenoid (115V), this kit also comes with a door strike and an ice door assembly. Please be advised the spring and roll pin are not included with this kit.

Videos For installing this part.

Replacing your Ice Dispenser Solenoid and Door Kit

Replacing your Ice Dispenser Solenoid and Door Kit play video
Questions and Answers

Questions and Answers

Be the first to ask our experts a question about this part!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.4 / 5.0, 4 reviews.
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
  • Customer:
    Alexander from Newport Beach, CA
  • Parts Used:
    61004388, 12001991
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Ice door broken
I watched the video (twice). Then followed the steps shown in the video and it was easy. I ordered the Ice door return spring but did not use as the original was intact. Likewise, I did not have to use the solenoid. The original is still working.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Alex from Westerville, OH
  • Parts Used:
    12001991
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Ice door broke
Watched a video on line. Unscrewed 5 screws holding face plate on. Inplugged the wire to the face plate. Replaced the arm holding the ice door and the solenoid. Used the old spring. Replugged the wire to the face plate and screwed it back on. Ice and water back in operation.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    George from Collegeville, PA
  • Parts Used:
    12001991
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
The refrigerator ice dispenser door (round flapper) had a broken attachment ear.
I watched the video and duplicated the steps shown. It's not likely that I could have completed the repair without the video. All steps were shown in detail and I went back to the video when I forgot some steps. Since I only needed to replace the flapper, I decided not to replace the working solenoid and will keep the new one in reserve. The steps to replace the solenoid are very simple had I replaced it. It would have helped had I written down the most important steps. Initially, I got an estimate for the repair which was unacceptable, so I decided to try it first myself. Even though the spring didn't need replacement, it would have been good to have in the kit since it seemed to be an inexpensive part. If you're handy at all, I would recommend doing the repair yourself.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Craig from E. Fairfield, VT
  • Parts Used:
    61004388, 61003804, 12001991
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Parts of Ice Dispenser Assembly fell into my cup
I followed the lead of the professional video provided so will not go into details on what I did. I'll just add a few of my hurdles that I ran into. Pay close attention to the video on how the solenoid stem fits onto the plastic assembly. I didn't get that exactly correct the 1st time around and first try didn't go well. I also had a problem with the 'CUBE' option being selected after reassembly. I had to clean the contacts up on the printed circuit board. I used an eraser which didn't seem to work. Then used a small screwdriver to remove a small film off from the contacts. Finally got the cube selection to work. I believe these new parts will also help in preventing the dispenser from frosting up. Won't know for sure until summer time but when its humid out our ice assembly would frost up often. The new ice shute flapper seems to seal much better than the old one because the seal had practically worn away on the old one. Again, watch the professional video. It is an exact representation of what needs to be done.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Model Compatibility
This part works with the following models:
Fix Number: FIX2003478
Manufacturer Part Number: 12001991
Brand
Model Number
Description
Kenmore
61004752
Refrigerator
Kenmore
61004753
Refrigerator
Kenmore
61004754
Refrigerator
Amana
ARS2760BW
Refrigerator - Side-by-side
Admiral
ASD2120DRQ
Refrigerator - Side-by-side
Admiral
ASD2120DRW
Refrigerator - Side-by-side
Admiral
ASD2123DRA
Refrigerator - Side-by-side
Admiral
ASD2123DRQ
Refrigerator - Side-by-side
Admiral
ASD2123DRW
Refrigerator - Side-by-side
Admiral
ASD2514ARA
Refrigerator - Side-by-side
Admiral
ASD2514ARQ
Refrigerator - Side-by-side
Admiral
ASD2514ARW
Refrigerator - Side-by-side
Crosley
CS21A5DA
Refrigerator - Side-by-side
Crosley
CS21A5DW
Refrigerator - Side-by-side
Crosley
CS21B5DA
Refrigerator - Side-by-side
Crosley
CS21B5DQ
Refrigerator - Side-by-side
Crosley
CS21B5DW
Refrigerator - Side-by-side
Crosley
CS21F5DW
Refrigerator - Side-by-side
Crosley
CS21G5DQ
Refrigerator - Side-by-side
Crosley
CS21G5DW
Refrigerator - Side-by-side
Crosley
CS23A6DA
Refrigerator - Side-by-side
Crosley
CS23A6DW
Refrigerator - Side-by-side
Crosley
CS23B6DA
Refrigerator - Side-by-side
Crosley
CS23B6DQ
Refrigerator - Side-by-side
Crosley
CS23B6DW
Refrigerator - Side-by-side
Crosley
CS24G6DB
Refrigerator - Side-by-side
Crosley
CS24G6DQ
Refrigerator - Side-by-side
Crosley
CS24G6DW
Refrigerator - Side-by-side
Crosley
CS25A7DA
Refrigerator - Side-by-side
Crosley
CS25A7DQ
Refrigerator - Side-by-side