Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
Dispenser Actuator
$42.02
In Stock
- Fix Number:
- FIX11748745
- Manufacturer #:
- WPW10131124
- Manufactured by:
- Whirlpool
- Product Description
- Also known as a paddle. Once a glass is pressed against the actuator it will cause the dispenser to deliver ice or water when activated.
- Works with the following brands:
- Maytag
- Works with the following products
- Refrigerator
- Fixes the following symptoms
- Not dispensing water, Ice maker won’t dispense ice
- Part# WPW10131124 replaces these:
- AP6015466, W10131124
Part Number Cross Reference
Product Description
Also known as a paddle. Once a glass is pressed against the actuator it will cause the dispenser to deliver ice or water when activated.
-
Works with the following brands:Maytag
-
Works with the following products:Refrigerator
-
Fixes the following symptoms:Not dispensing water, Ice maker won’t dispense ice
-
Part# WPW10131124 replaces these:AP6015466, W10131124
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts Additional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
- Customer:
- Bruce from Central Point, OR
- Parts Used:
- WPW10131124, WP12565502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice and Water Dispenser did not work. Paddle was warped and jammed into the recess behind the light switch area. Replaced the paddle unit.
Removed the Drip tray and removed the two hex screws at the bottom with a nut driver. detached the face plate by pushing up. (pops off) Removed the two hex screws securing the dispenser assembly and pulled it out to access the wiring to the control board. Unplugged the wiring and removed the control panel and face plate to access the p
... Read more
addle/spring assembly. Used the needle nose pliers to remove the spring from the paddle assembly, popped out the paddle where it snaps in on the side opposite the spring. Fish the spring end of the paddle out of the pivot hole and reinstall the new paddle unit and spring by reversing the above process. Reassemble the wiring harnesses onto the control board and attach the ice/water assembly with the two hex screws at the top using the nut driver. Replace the face plate and reinstall the two hex screws at the bottom. Snap the face plate back into place and replace the drip tray.
Read less
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Graham, NC
- Parts Used:
- WPW10131124, W11395888
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Paddle broken -no ice or water
Start by removing the lower drip pan exposing the two nuts that hold on the outer trim. Remove the two 5/16 screws and gently pry the trim molding loose from the door. The entire touch pad and trim will come off leaving only three connections to carefully unplug. Once this is removed, there are two additional 5/16 screws holding the mecha
... Read more
nism in place in the door. Remove screws, remove the mechanism and dislodge the hose from the clips that secure it in its place. Once this is done, all is left is to pry open the slot where the paddle rests being careful of the spring, and place the new paddle assuring the spring is in the proper slot. I had to slightly bend the end of the paddle in order to make better contact with the switch that operates the ice and water. I fine tuned this to operate with a very soft touch. Once the paddle is changed, and operates smoothly, reassemble mechanism, water tube, screws, and reattach plugs to the touch pad. Snap cover in place, return two remaining screws, and enjoy. Thank you.
Read less
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX11748745
Manufacturer Part Number: WPW10131124
Manufacturer Part Number: WPW10131124
Brand
Model Number
Description
✖
Mail-In Recycling Rebate