OEM General Electric Range Temperature Sensor [WB21X22134] | Ships Today | Fix.com

Temperature Sensor

&SeePartX&
Temperature Sensor – Part Number: WB21X22134
https://fixcom.azureedge.net/Schematics/GE/00115410i02.gif
Click for the BBB Business Review of this Appliances - Small - Supplies & Parts in Dartmouth NS
Part Description:
This temperature sensor detects the temperature within the oven cavity.
This part works with the following brands:
Part number cross reference:
This part works with the following products:
Range, Wall Oven, Microwave Oven Combo.

Installation Instructions

Showing 1-10 of 10 Instructions

Oven temperature was erratic and finally would not preheat.

I was lucky to stumble on this website. There seemed to be many with the same problem. I ordered the part and hoped for the best. It arrived and I installed just as others had described. First, I unplugged the range. Removed the back cover (a central panel) with 4 screws. Familiarized myself with the plug-in thermal sensor. Went around front and loosened the single set screw for the probe (near the top of oven). Threaded the bad element out and rethreaded the new element from the front. In back, reinstall the plastic plug-in connector. Tightened set screw in the oven, plugged it in and tested. It worked! Put the back on and it was done. It took 31 minutes. Actually took longer to clean behind the stave than the repair. Thanks to all for advice.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Stuart from Parrish, FL

Oven not heating at all

I attempted to replace the temperature sensor but in removing it I noticed both broil and bake elements damaged on the undersides. Replaced all and the stove is working better than new.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Very Easy
Total Repair Time: Less than 15 mins
Tools: Socket set
Customer: Rosemary from District heightx, MD

After trying to clean my oven twice , I got on your site and found what the problem may be

This is the second time I used your service , ie washer, timer, this time was my oven.. For 12$ I fix my oven in 15 minutes, I'll never call a service company that charges 75 to 125 per hour, 75 if they just come in your house.. I fixed it in 15 minutes.. I'm sold on your cost and your tech service, I'm no mr fix it but this was so easy three bolts and plug in the new thermostat works like new GE

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Really Easy
Total Repair Time: Less than 15 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Marty from Stafford, VA

Lower oven not heating hot enough

Removed the 6-8 hex head screws holding the back panel of the range on. Located the sensor plug, unplugged the sensor wire that goes through the insulation into the lower oven. Inside the lower oven cavity, removed 2 hex screws holding the sensor unit on. Removed old sensor unit. Did reverse to install the new one. Only slight issue was needing to get the plug end through the insulation on the back of the range but really no big deal.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Very Easy
Total Repair Time: Less than 15 mins
Tools: Nutdriver
Customer: Brian from Gig Harbor, WA

My oven would not reach the correct temp, it kept turning off before it would get really hot.

The repair was effortless. I just removed the screw with a nut driver, then pulled out the old part with needle nose pliers, unplugged the old part and plugged in the new part. I then put the one screw back in, and the job was done! The whole job took 10 - 15 minutes. Oven is now back in working order. If i had to do the job again it could be done in 5 minutes.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Very Easy
Total Repair Time: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: johnny from brea, CA

Electric oven was not heating up on convection or convention.

Unplug oven, take off back center plate removing 5-6 hexagon screws with socket set. Disconnect wire of thermostat. Open door of oven look up near upper heating element, one hex screw holding thermostat in place, remove and pull through hole.Install new thermostat, in reverse order of steps.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Easy
Total Repair Time: 15 - 30 mins
Tools: Socket set
Customer: Christopher from Williston, VT

Stove was not heating to the right temp and was taking too long to preheat.

This repair was very easy. It didn't turn out to be the problem but I thought I would try this route first since it was such a cheap part. In any case, I took the five screws off of the back and unscrewed the screw holding in the old part from the inside of the stove. It was simply an act of un-clipping the old part, pulling it out, and re-clipping the new one. Then simply screw everything back in place. I didn't take long at all.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Very Easy
Total Repair Time: Less than 15 mins
Tools: Nutdriver
Customer: Melodie from Front Royal, VA

Heating inconsistent

REPLACED THERMOSTAT (SENSOR ASSEMBLY). PULL STOVE AWAY FROM WALL, UNPLUG AC/ TURN OFF GAS SHUTOFF VALVE. IF FURNACE HAS LONG GAS LINE, CAREFULLY PULL FOR WORK SPACE. WITH NUT DRIVER, LOOSEN 1/4 NUT BACK OF STOVE TO REMOVE CENTER COVER, AND LOOSEN 2 , 1/4 NUT SENSOR ASSEMBLY INSIDE TOP RIGHT OVEN. REPLACE AND PLUG BACK COMPONENT.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Nutdriver
Customer: Clifford from Simi Valley, CA

F4 code on oven, issues with thermometer

Simply unplugged oven, unscrewed part from inside, removed backing of oven, unclipped old wire, removed part from oven, pushed new wires through, attached new part, connected wires in back, wahlah!

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Really Easy
Total Repair Time: Less than 15 mins
Tools: Socket set
Customer: Heidi from Portland, ME

Range would not pre heat

Removed old sensor screwed in new sensor, plugged sensor in and tested. Works great.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Temperature Sensor
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Nutdriver
Customer: John from Vancouver, WA
Showing 1-10 of 10 Instructions

Model Cross Reference List

This part works with the following models:

Fix Number: FIX10059162
Manufacturer Part Number: WB21X22134


Brand
Model Number
Description
General Electric
155910
Range
General Electric
15891 1
Range
General Electric
158911
Range
Kenmore
91147619200
Range
Kenmore
91147619201
Wall Oven
Kenmore
91147643100
Wall Oven
Kenmore
91147692100
Microwave Oven Combo
Kenmore
91147699100
Microwave - 27" ELECTRIC BUILT-IN OVEN
Kenmore
91147702200
Wall Oven
Kenmore
91147702201
Wall Oven
Kenmore
91147703200
Wall Oven
Kenmore
91147703201
Wall Oven
Kenmore
91147704200
Wall Oven
Kenmore
91147704201
Wall Oven
Kenmore
91147709200
Wall Oven
Kenmore
91147709201
Wall Oven
Kenmore
91147722200
Range
Kenmore
91147722201
Wall Oven
Kenmore
91147722202
Wall Oven
Kenmore
91147724200
Range
Kenmore
91147724201
Wall Oven
Kenmore
91147724202
Wall Oven
Kenmore
91147729200
Range
Kenmore
91147729201
Wall Oven
Kenmore
91147729202
Wall Oven
Kenmore
91147742200
Wall Oven
Kenmore
91147742201
Wall Oven
Kenmore
91147743200
Wall Oven
Kenmore
91147743201
Wall Oven
Kenmore
91147744200
Wall Oven