OEM Frigidaire Range Oven Probe [316490000] | Ships Today | Fix.com
Oven Probe – Part Number: 316490000
( Grid squares measure 1x1 inch )
Oven Probe – Part Number: 316490000 https://fixcom.azureedge.net/Schematics/Frigidaire/MOHEIM5W.gif

Oven Probe

Fix Number: FIX1528542

Manufacturer #: 316490000

Manufactured by: Frigidaire

Part description

This temperature sensor detects the temperature within the oven cavity.

Works with the following brands

Frigidaire, Kenmore, Crosley, Electrolux, Tappan, Kelvinator, Westinghouse, Gibson

Works with the following products

Range, Wall Oven

Fixes the following symptoms

Oven is too hot | Little to no heat when baking | Oven not heating evenly | Will Not Start

Installation InstructionsProvided by FIX customers like you

Average Repair Rating: 3.5 / 5.0, 5 reviews ?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
mark from Traverse City, MI
Parts Used:
316075103, 316490000
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set
f10 when we used oven
pulled stove out, remove power cord from wall,remove back and replace parts .
2 of 4 people found this instruction helpful.
Were these instructions helpful?
Customer:
Greg from Belle Plaine, KS
Parts Used:
316490000
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven was inconsistent on heat, typically way over-heating
Replacing the oven probe is very straightforward, I tested the old one with a multi-meter after pulling the range out (had to disconnect the gas line and unplug the range...the most difficult part of the repair, lol!) and determined it was bad; purchased the new one from this site. The probe is located in the back of the oven, easy to see once the rear shroud was taken off the range (6 screws), especially having the new one in hand and knowing what to look for. One screw held it in place, and there is a single plug to disconnect. Installation is the reverse of removal. Pushed the range back into place, reconnected the gas line and plugged it in. Repair was perfect. Saved a ton of money, for sure!
1 person found this instruction helpful.
Were these instructions helpful?
Customer:
Jan from OLEY, PA
Parts Used:
316490000
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
oven did not work
replaced oven probe did. Did not solve problem. Returned probe, ordered oven control. Replaced the control and fixed the problem. Biggest problem was that the new control did not come with the graphics sheet. Had to carefully remove from old control and install on new unit.
1 person found this instruction helpful.
Were these instructions helpful?
Customer:
Paul from Chicopee, MA
Parts Used:
316490000
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Bake element not heating
First tried heat probe replacement but bake element still not heating. Replaced control board solving problem. Easy installation.
1 person found this instruction helpful.
Were these instructions helpful?
Customer:
Colton from Vernal, UT
Parts Used:
316490000
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Oven Probe was not the problem, Had to Replace the OCU
After removing the back and testing the Oven Probe found that it was OK. replaced it anyway. Using a Volt- Ohm meter I found that the K-1 relay was bad (no 220 volts out of the OCU ordered a new one. Your Parts dept.were very helpful with the order. Had to use dental floss (slid it between the original OCU and the benzyl) to remove it. Then stuck it on the front of the new OCU, replaced the board and back,everything worked great. Thank you for the parts help.
0 of 1 people found this instruction helpful.
Were these instructions helpful?