OEM Makita Router Parts | Expert DIY Repair Help & Fast Shipping

$9.94

Carbon Brush Set CB-303

Fix Number FIX10156649

Manufacturer Part Number CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

$9.94

Carbon Brush Set

Fix Number FIX10156641

Manufacturer Part Number CB154

This motor brush set is for power tools. Motor brush set transfers electric current to the spinning armature in the motor. The set includes both motor brushes.

$19.74

Power Cord

Fix Number FIX10153834

Manufacturer Part Number 664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

$26.90

Power Cord - 8', 14 Gauge, 2-Wire

Fix Number FIX10153852

Manufacturer Part Number 664463-0

This power cord includes 2 prongs, 2 wires, and the gauge is 14. The measurement is 8 feet long and the type is bare wire. The cord is used on various power tools, specifically gardening and lawn equipment. With use and time, power tool cords can become frayed. If there are visible signs of wear on your cord, it is important to replace it immediately. For safety practices and installation instructions, refer to the diagram provided by the manufacturer.

$9.94

Carbon Brush Set CB-408 6x9mm

Fix Number FIX10156657

Manufacturer Part Number CB408

This part includes two carbon brushes with wire leads and brush springs. Worn brushes are typically presented as a failed or underperforming motor. Carbon brushes are a part that commonly wears, so it is a good idea to have these on hand. They are essential for a properly running motor because they conduct electricity to the armature. For this repair, you will start by removing the first brush from the motor, using a screwdriver to remove the brush cap. Once the cap is removed, the brush can be removed. Align the new brush with the holder and then reinstall the cap. Repeat these same steps for the other brush.

$2.99

Cord Guard / Strain Reliever

★★★★★

1 Review

Fix Number FIX10153921

Manufacturer Part Number 682505-8

This cord guard or strain reliever prevents cord damage by covering the last portion of a cord before entering a tool. This provides extra support and rigidness. The cord fits garden and lawn equipment. With use, the cord guard can break down and your cord is left unprotected, in this case it is best to replace the guard. Refer to the diagram provided by the manufacturer for installation instructions.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

$4.15

Base Protector

Fix Number FIX10151953

Manufacturer Part Number 454842-8

$12.70

Carbon Brush Set CB-203

Fix Number FIX10156645

Manufacturer Part Number CB203

This part includes two carbon brushes with the wire leads and brush springs attached. In order for your motor to run at peak performance, it is imperative that the carbon brushes are well-maintained. The carbon brushes are needed to conduct electricity to the armature through the commutator. Over time these brushes wear down due to the constant rubbing. They should be regularly inspected to ensure your equipment continues to run smoothly. This repair should only take a few minutes.