OEM Makita Impact Driver Parts & Accessories

Carbon Brush Set

$10.85

Fix Number: FIX10156641
Manufacturer Part Number: CB154

This motor brush set is for power tools. Motor brush set transfers electric current to the spinning armature in the motor. The set includes both motor brushes.

Watch the install video

Power Cord

$21.97

Fix Number: FIX10153834
Manufacturer Part Number: 664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Watch the install video

Carbon Brush Set

$6.36

Fix Number: FIX10156662
Manufacturer Part Number: CB440

The brush box kit fits a variety of cordless gardening tools. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder. Due to friction, carbon brushes are common replacement parts. If the functioning of your motor changes and does not work, then check if the brush is worn out or inspect the wire lead for cracks, burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions.

Power Tool Power Cord

$23.43

★★★★★

1 Review

Fix Number: FIX10153842
Manufacturer Part Number: 664265-4

This power cord is for power tools. Unplug the power tool before installing this part. Wear work gloves to protect your hands.

Carbon Brush CB-124 (Set of 2)

$7.83

★★★★★

1 Review

Fix Number: FIX10156640
Manufacturer Part Number: CB124

Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will need to be replaced. If you are experiencing excessive sparks, this can also be caused by a damaged armature, so it is best to check it at the same time. This part includes two carbon brushes, which need to be replaced at the same time.

Watch the install video

Carbon Brush Set CB-408 6x9mm

$10.85

Fix Number: FIX10156657
Manufacturer Part Number: CB408

This part includes two carbon brushes with wire leads and brush springs. Worn brushes are typically presented as a failed or underperforming motor. Carbon brushes are a part that commonly wears, so it is a good idea to have these on hand. They are essential for a properly running motor because they conduct electricity to the armature. For this repair, you will start by removing the first brush from the motor, using a screwdriver to remove the brush cap. Once the cap is removed, the brush can be removed. Align the new brush with the holder and then reinstall the cap. Repeat these same steps for the other brush.

Cord Guard / Strain Reliever

$3.99

★★★★★

1 Review

Fix Number: FIX10153921
Manufacturer Part Number: 682505-8

This cord guard or strain reliever prevents cord damage by covering the last portion of a cord before entering a tool. This provides extra support and rigidness. The cord fits garden and lawn equipment. With use, the cord guard can break down and your cord is left unprotected, in this case it is best to replace the guard. Refer to the diagram provided by the manufacturer for installation instructions.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Carbon Brush Set CB-441

$6.36

Fix Number: FIX10156663
Manufacturer Part Number: CB441

This is a set of two carbon brushes. The carbon brushes should be checked on a regular basis. If they have worn down to the limit mark, it is time for a replacement. Both carbon brushes need to be replaced at the same time. For this repair use your screwdriver to detach the brush holder caps, remove the old carbon brushes, and insert the new ones. Fasten the new carbon brushes to the holder caps. To break in the new carbon brushes, run the tool with no load for about one minute.

Brush Holder Cap 6.513.5

$4.99

Fix Number: FIX10153352
Manufacturer Part Number: 643650-4

This is a brush holder cap for a variety of power tools. The cap contains the brush in the holder. It protects the motor brush on the motor brush holder by covering it. To remove the cap, you will need a slotted screwdriver. Do not press hard when removing this part, they break easily under pressure.

Steel Ball 3.5

$4.99

Fix Number: FIX10142080
Manufacturer Part Number: 216001-0

Makita Impact Driver Parts

Popular Makita Impact Driver Parts

Installation Instructions

Installation Instructions

Appliance Type

Related Pages

Popular Makita Impact Driver Models

Makita Impact Driver Parts

Start With Your Model Number

Popular Makita Impact Driver Parts

Installation Instructions

Installation Instructions

Appliance Type

Related Pages

Popular Makita Impact Driver Models